Yard Force LX SPP10 Original Instructions Manual

The Yard Force LX SPP10 is a robust and efficient pressure washer designed for domestic and light commercial use. It features a high-pressure pump, multiple spray nozzles, detergent tank, adjustable pressure settings, thermal protection, and a durable frame with wheels for easy mobility. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: High-pressure pump, Spray gun, Detergent tank, Adjustable nozzle tips, Thermal overload protection, Wheels and handle for transport.

Assembly & Installation

Unpack all components and check against the parts list. Assemble on a flat, stable surface.

1. Attach wheels: Insert axle through frame and secure wheels with provided clips.
2. Install handle: Extend telescopic handle to desired height and tighten locking mechanism.
3. Connect high-pressure hose: Attach one end to pump outlet and the other to spray gun.
4. Install water inlet filter: Connect to pump inlet and attach garden hose.
5. Fill detergent tank: Remove cap, add appropriate cleaning solution, and replace securely.

WARNING! Ensure all connections are tight before operation. Do not overtighten plastic fittings.

First-Time Setup

Prepare the pressure washer for initial use following these steps.

1. Water connection: Connect garden hose to water inlet. Ensure water supply is turned on.
2. Power connection: Plug into grounded 230V AC outlet (check local voltage requirements).
3. Prime the pump: Turn on water supply and squeeze spray gun trigger until steady water flow appears.
4. Select nozzle: Choose appropriate spray tip for your cleaning task.
5. Test operation: Turn power switch ON and test spray pattern at low pressure first.

CAUTION! Never operate the pump without water supply as this can cause immediate damage.

Specifications

• Model: Yard Force LX SPP10
• Maximum Pressure: 130 bar (1885 PSI)
• Water Flow: 420 L/h (1.85 GPM)
• Motor Power: 1800W
• Voltage: 230V AC, 50Hz
• Hose Length: 6 meters (19.7 feet)
• Detergent Tank Capacity: 1 liter (0.26 gallons)
• Nozzle Types: 0° (red), 15° (yellow), 25° (green), 40° (white), soap (black)
• Dimensions (LxWxH): 480 x 350 x 380 mm
• Weight: 12.5 kg (27.6 lbs)

Controls and Settings

Main control panel located on top of the unit. Spray gun with adjustable nozzle selector.

Control Panel: Power switch with LED indicator, Pressure adjustment knob, Thermal reset button.

Spray Gun: Trigger with safety lock, Quick-connect nozzle adapter, Detergent selection dial. Pressure Settings: Adjust from 80-130 bar using control knob. Detergent Application: Turn dial to "SOAP" position for detergent application, then switch to rinse mode. Thermal Protection: Automatic shut-off activates at 130°C; reset button pops out when cooled.

Connecting Accessories

Compatible with standard pressure washer accessories using quick-connect system.

1. Turn off pressure washer and disconnect from power.
2. Select appropriate nozzle for task (0° for stubborn stains, 40° for gentle cleaning).
3. Push nozzle into quick-connect adapter until it clicks securely.
4. For extension wands: Connect between hose and spray gun using provided adapters.
5. For surface cleaners: Attach to spray gun using quick-connect system.

Tip: Always start with widest spray pattern (40°) and increase pressure as needed.

Operation Guide

Follow proper sequence for safe and effective operation.

1. Preparation: Connect water supply, ensure area is clear of obstacles.
2. Power on: Turn switch to ON position; LED indicator will illuminate.
3. Select mode: Turn nozzle to desired setting or detergent application.
4. Begin cleaning: Hold spray gun firmly, release safety lock, squeeze trigger.
5. Adjust pressure: Use control knob to increase/decrease pressure during operation.
6. Apply detergent: Turn dial to soap position, apply solution, let sit 5-10 minutes.
7. Rinse: Switch to appropriate rinse nozzle and remove detergent residue.
8. Shutdown: Release trigger, engage safety lock, turn power OFF, disconnect from outlet.

WARNING! Never point spray gun at people, animals, or electrical equipment. Maintain safe distance of at least 1 meter from surface being cleaned.

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. After each use: Flush system with clean water for 2 minutes.
2. Monthly: Check and clean water inlet filter; replace if damaged.
3. Seasonal: Inspect high-pressure hose for cracks or wear; replace if necessary.
4. Storage: Drain all water, store in dry location protected from freezing temperatures.
5. Pump maintenance: Use pump protector fluid if storing for extended periods.

CAUTION! Always disconnect from power before performing any maintenance. Never use harsh chemicals to clean the unit.

Safety Information

Read all instructions before operation. Wear appropriate personal protective equipment.

• Always wear safety glasses and sturdy footwear.
• Keep children and pets away from work area.
• Never modify or bypass safety features.
• Use only Yard Force approved accessories and parts.
• Do not operate unit if damaged or leaking.
• Keep electrical connections dry and protected from water spray.
• Maximum water temperature: 40°C (104°F).

DANGER! High-pressure spray can cause serious injury. Test spray pattern away from work area first.

Regulatory Information

CE Certified: Complies with European safety standards. IP Rating: IPX5 water resistance. Waste Electrical and Electronic Equipment (WEEE): Do not dispose with household waste. Contact local authorities for recycling information. Copyright © 2023 Yard Force. All rights reserved. For support, visit www.yardforce.com or contact customer service at +44 (0) 1234 567890.

Troubleshooting

Reset Procedure: Turn power OFF, wait 30 seconds, then restart. For thermal overload, press reset button after cooling.

Service: +44 (0) 1234 567890; www.yardforce.com/support