Xtm Tracer 3906BP OwnerS Instruction Manual

The Xtm Tracer 3906BP is a high-performance marine GPS chartplotter with a 7-inch sunlight-readable display, built-in global basemap, preloaded C-MAP® charts, dual-channel GPS+GLONASS receiver, IPX7 waterproof rating, microSD card slot for additional maps, NMEA 0183/2000 connectivity, and internal rechargeable battery. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Using Navigation Features 8. Data Management 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 7-inch LCD display with capacitive touch, Power/Menu button, microSD card slot, USB-C data/power port, NMEA 2000 connector, external antenna port, mounting bracket.

Feature	Description
Display	7-inch, 800 x 480 pixels, sunlight readable, capacitive touch
GPS Receiver	Dual-channel GPS+GLONASS with WAAS/EGNOS
Charts	Preloaded C-MAP® Coastal Charts, global basemap
Waterproof Rating	IPX7 (submersible to 1m for 30 minutes)
Connectivity	NMEA 0183/2000, USB-C, microSD card slot
Power	10-32V DC, internal Li-ion battery backup
Mounting	Quick-release bracket with tilt/swivel
POWER/MENU Button	Turns unit on/off; accesses main menu
microSD Slot	For additional chart data and software updates
USB-C Port	For data transfer and power supply

Installation

Unpack and inspect contents. Choose mounting location carefully.

Mount bracket: Select location with clear view, secure using supplied hardware.
Connect power: Route 10-32V DC power cable to battery; use in-line fuse.
Connect antennas: Attach external GPS antenna if required for better reception.
Connect NMEA devices: Wire NMEA 0183 or connect NMEA 2000 backbone.
Secure unit: Snap chartplotter onto bracket; tighten locking knob.

WARNING! Ensure all electrical connections are waterproofed. Route cables away from moving parts and heat sources.

First-Time Setup

Power on unit; follow initial setup wizard.

Select language: Choose from available options (default ENGLISH).
Set units: Configure nautical/miles, feet/meters, magnetic/true north.
Acquire GPS signal: Place unit in open sky; wait for satellite lock.
Calibrate compass: Follow on-screen instructions if equipped.
Configure chart preferences: Set depth contours, chart colors, etc.

CAUTION! Do not power on before securing mounting bracket. Ensure waterproof seals are intact.

Specifications

Display: 7-inch TFT LCD, 800 x 480, capacitive touch.
GPS: Dual GPS+GLONASS, 3m accuracy typical.
Charts: Preloaded C-MAP® Coastal, supports C-MAP 4D.
Memory: 8GB internal, microSD slot (up to 32GB).
Connectivity: NMEA 0183 (2x), NMEA 2000, USB-C.
Power: 10-32V DC, 1.5A max; internal Li-ion backup (8 hrs).
Waterproof: IPX7.
Operating Temp: -15°C to 55°C.
Dimensions: 195 x 130 x 55 mm.

Controls and Settings

Access menus via touchscreen or POWER/MENU button. Home Screen: Provides quick access to Chart, Sonar (if connected), Routes, Waypoints.

Touch Gestures: Tap to select, drag to pan chart, pinch to zoom.

Settings Menu: System (Language, Units, Backlight), Chart (Overlays, Depth Shading), Navigation (Route Planning, Alarms), Communication (NMEA Setup), Sonar (Frequency, Range). Waypoints/Routes: Create, edit, navigate to. Tracks: Record and review track history.

Connecting Devices

NMEA 0183: Connect to compatible instruments (speed, depth). NMEA 2000: Plug into backbone for autopilot, engine data. Sonar: Connect compatible transducer via adapter cable.

Power off all devices before connecting.
Use marine-grade cables and connectors.
Seal connections with dielectric grease and heat shrink.
Configure NMEA data sources in Communication menu.

Tip: Test all connections at dock before departure.

Using Navigation Features

Supports waypoint navigation, route planning, track recording.

Create waypoint: Tap chart location, select "Mark Waypoint."
Plan route: Tap "New Route," add waypoints in sequence.
Navigate: Select route or waypoint, tap "Navigate To."
Follow course: Screen shows bearing, distance, XTE, ETA.
Record track: Enable track recording in Navigation menu.
Use alarms: Set anchor drag, arrival, off-course alarms.
View tide/current: Access from Chart menu if data available.
Man overboard (MOB): Press and hold POWER/MENU button for 3 seconds.

WARNING! Always have paper charts as backup. GPS signals can be interrupted.

Data Management

Waypoints/Routes: Export/import via USB or microSD in GPX format. Software Updates: Download updates to microSD, install via System menu. Chart Updates: Purchase and load via C-MAP® Chart Manager.

Care & Cleaning

Power off and disconnect before cleaning. Use fresh water and mild soap on exterior. Wipe screen with soft, damp cloth; avoid abrasive cleaners.

CAUTION! Do not use high-pressure water spray. Ensure USB and card slot covers are closed when not in use.

Regulatory Information

FCC Part 15: Class B digital device; complies with limits for marine use. CE certified. Contains GPS receiver regulated under ITU-R M.823-3. Copyright © 2023 Xtm Marine; trademarks of Xtm Marine Ltd. For support, visit www.xtm-marine.com or contact +1-800-555-3906.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power connection/fuse	Check battery voltage; verify in-line fuse; ensure connections are dry and tight.
No GPS signal	Antenna/obstruction	Move to open area; check antenna connection; verify GPS is enabled in settings.
Touchscreen unresponsive	Screen protector/calibration	Remove aftermarket screen protector; recalibrate touchscreen in System menu.
Charts not displaying	Card corruption/region	Reinsert microSD card; ensure charts are for correct region; format card if needed.
NMEA data missing	Wiring/settings	Check NMEA wiring; verify baud rate matches source; enable correct sentences in menu.

Reset: System > Factory Reset (erases all user data).

Service: +1-800-555-3906; www.xtm-marine.com/support