Xantrex 710-0010 Owner's Manual

The Xantrex 710-0010 is a high-performance power inverter designed for reliable AC power from DC sources. It features pure sine wave output, multiple protection systems, remote control capability, and compatibility with various battery types. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operation Modes 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Pure sine wave inverter, Remote Control Panel, DC input terminals, AC output outlets, Cooling fan, Status indicators.

Feature	Description
Pure Sine Wave Output	Clean power compatible with sensitive electronics
High Efficiency	Up to 90% efficiency rating
Remote Control Capability	Optional remote panel for monitoring and control
Multiple Protection	Overload, over-temperature, low battery shutdown
DC Input Terminals	For battery connection (12V/24V/48V systems)
AC Output Outlets	Standard household outlets (120V AC)
Cooling Fan	Thermally controlled for optimal operation
Status Indicators	LED display for power, fault, and battery status
Battery Compatibility	Works with lead-acid, AGM, gel, and lithium batteries
Power ON/OFF	Main power switch and remote enable/disable

Installation

Unpack and inspect contents. Mount in well-ventilated area.

Choose location: Dry, cool area with adequate airflow.
Mount inverter: Secure using provided brackets or mounting hardware.
Connect batteries: Use appropriate cables to DC input terminals.
Connect AC loads: Plug devices into AC output outlets.
Connect remote panel: Attach optional remote control cable.

WARNING! Ensure proper ventilation. Use correct cable sizes. Follow all safety guidelines.

First-Time Setup

Power on inverter; check status indicators.

Verify connections: Ensure all DC and AC connections are secure.
Set battery type: Configure for your specific battery chemistry.
Set output voltage: Confirm 120V AC output setting.
Test operation: Connect small load to verify proper function.
Configure remote: Set up optional remote panel if installed.

CAUTION! Double-check polarity on DC connections. Start with minimal load during testing.

Specifications

Model: Xantrex 710-0010
Continuous Power: 1000W
Surge Power: 2000W (30 seconds)
Input Voltage: 12V/24V/48V DC (selectable)
Output Voltage: 120V AC ±3%
Output Frequency: 60Hz ±0.1%
Waveform: Pure sine wave
Efficiency: Up to 90%
Protections: Overload, short circuit, over-temperature, low/high voltage
Operating Temperature: -20°C to 50°C (-4°F to 122°F)
Dimensions: Standard 19-inch rack mount or standalone
Weight: Approximately 15 lbs (6.8 kg)

Controls and Settings

Access settings via front panel or remote control. Front Panel: Power switch, Status LEDs, Fault reset button.

Remote Panel: Power ON/OFF, Voltage display, Current display, Fault indicators, Configuration buttons.

Configuration: Battery type (FLOODED, AGM, GEL, LITHIUM), Low voltage cutoff, Search mode sensitivity, Output voltage adjustment. Status Indicators: Power (green), Fault (red), Battery low (yellow), Over-temperature (red).

Connecting Devices

DC Input: Battery terminals (positive/negative). AC Output: Standard household outlets. Remote: RJ45 connector.

Turn off all power sources before connecting.
Connect batteries first: Positive then negative terminals.
Connect AC loads: Plug devices into outlets.
Connect remote: Attach remote panel cable if used.
Power sequence: Battery first, then inverter, then loads.

Tip: Use appropriate fuses or circuit breakers on DC connections.

Operation Modes

Supports continuous, standby, and search modes.

Normal operation: Provides continuous AC power when enabled.
Standby mode: Low power consumption when no load detected.
Search mode: Periodically checks for load connection.
Battery save: Reduces idle current when in standby.
Remote operation: Control via optional remote panel.
Parallel operation: Can be paralleled with identical units.
Load management: Automatically adjusts to load demands.
Fault recovery: Auto-reset after certain fault conditions.

WARNING! Do not exceed rated power capacity. Monitor battery voltage during operation.

Safety Features

Overload Protection: Shuts down if load exceeds rating. Thermal Protection: Reduces output or shuts down if overheated. Low Battery Protection: Shuts down when battery voltage drops below set point. Short Circuit Protection: Immediate shutdown on output short. Reverse Polarity Protection: Protects against incorrect DC connection.

Care & Maintenance

Disconnect all power before maintenance. Keep clean and dust-free. Check connections periodically.

CAUTION! No user-serviceable parts inside. Refer to qualified technician for internal repairs.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL 458 certified for marine and vehicle use. CE marked for European compliance. Copyright © Xantrex LLC. For support, visit www.xantrex.com or contact 1-800-670-0707.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No output power	Battery low/disconnected	Check battery voltage and connections; recharge battery.
Inverter shuts down	Overload/over-temperature	Reduce load; ensure proper ventilation; allow to cool.
Fault light on	Various faults	Check error code; reset inverter; check connections.
Low efficiency	Poor connections/cabling	Check all connections; use proper cable sizes.
Remote not working	Cable/configuration	Check remote cable; verify remote address setting.
Audible alarm	Low battery/overload	Check battery voltage; reduce connected load.
Overheating	Insufficient ventilation	Improve airflow; clean air vents; reduce ambient temperature.

Reset: Power cycle or use reset button if available.

Service: 1-800-670-0707; www.xantrex.com