Wetelux 83 14 69 Instruction Manual

The Wetelux 83 14 69 is a premium multi-function shower panel system featuring a thermostatic mixing valve, multiple spray functions (rain, massage, jet), adjustable body jets, a handheld shower, a diverter valve, and a temperature memory function. Constructed with stainless steel and brass fittings, it includes a pressure-balancing mechanism, a digital temperature display, and an anti-scald safety device. Designed for 1/2" water supply lines, operating pressure 20-80 PSI. Below are key sections for safety, features, installation, setup, operation, and maintenance.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Water Supply 7. Operating the Shower System 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Main shower panel with thermostatic valve, Overhead rain showerhead, Adjustable body jets, Handheld shower on slide bar, Diverter valve, Digital temperature display, Pressure-balancing cartridge.

Feature	Description
Thermostatic Mixing Valve	Maintains constant water temperature
Overhead Rain Showerhead	12-inch diameter, provides wide coverage rainfall
Adjustable Body Jets	4 nozzles, angle adjustable ±30 degrees
Handheld Shower	5-spray pattern, mounted on 32-inch slide bar
Diverter Valve	Selects between overhead, handheld, and body jet functions
Digital Temperature Display	LED shows current water temperature in °C/°F
Pressure-Balancing Mechanism	Compensates for pressure fluctuations
Anti-Scald Safety Device	Limits maximum outlet temperature to 120°F (49°C)
Temperature Memory	Remembers last used temperature setting
Flow Rate Control	Adjusts water volume independently of temperature

Installation

Unpack and inspect all components. Ensure wall is structurally sound.

Shut off water supply: Turn off main water valves to bathroom.
Mount shower panel: Use provided template to mark drill points. Secure mounting bracket to wall studs.
Connect water supply: Connect hot and cold 1/2" supply lines to corresponding inlets on valve body.
Connect shower outlets: Attach overhead shower arm, body jet hoses, and handheld shower hose.
Seal connections: Apply thread seal tape to all threaded connections. Tighten securely.
Test for leaks: Turn water supply back on slowly and check all connections.

WARNING! Panel is heavy; use two people for mounting. Ensure all connections are watertight before use.

First-Time Setup

After installation, perform initial configuration.

Purge air from lines: Run water through all functions for 2 minutes to remove air.
Set temperature limit: Adjust safety stop on thermostatic valve to desired maximum (factory set to 120°F/49°C).
Calibrate display: Press and hold temperature button for 5 seconds to switch between °C and °F.
Adjust body jets: Point nozzles to desired angles before first use.
Test diverter: Cycle through all spray functions to ensure smooth operation.

CAUTION! Test water temperature carefully before entering shower. Initial water may be very hot.

Specifications

Model: Wetelux 83 14 69
Finish: Brushed stainless steel with chrome accents
Valve Type: Thermostatic with pressure balancing
Supply Connections: 1/2" NPT hot and cold inlets
Operating Pressure: 20-80 PSI (1.4-5.5 bar)
Maximum Flow Rate: 2.5 GPM (9.5 L/min) at 80 PSI
Temperature Range: 68°F to 120°F (20°C to 49°C)
Power Source: Self-powered (water pressure), display uses lithium battery (CR2032)
Dimensions: Panel: 24" W x 36" H; Rain shower: 12" diameter
Warranty: 5 years on valve, 2 years on finish

Controls and Settings

Main control knob: Turns water on/off and adjusts flow rate. Temperature control lever: Sets desired water temperature. Diverter knob: Selects between overhead, handheld, and body jet functions.

Digital Display: Shows current water temperature. Button below toggles °C/°F. Memory function automatically recalls last temperature setting.

Spray Functions: Overhead rain (fixed), Handheld (5 patterns: rain, massage, jet, mist, combination), Body jets (adjustable pressure). Temperature Safety: Anti-scald device limits maximum temperature. Pressure Balance: Automatically maintains consistent pressure if other fixtures are used.

Connecting Water Supply

Hot and cold: Standard 1/2" connections. Ensure proper orientation (H for hot, C for cold).

Turn off main water supply before connecting.
Use thread seal tape on all connections (wrap clockwise 3 times).
Connect hot water to left inlet (marked H), cold to right (marked C).
Tighten with adjustable wrench - do not overtighten.
Install included pressure regulators if supply pressure exceeds 80 PSI.

Tip: Install shut-off valves on both supply lines for easier maintenance.

Operating the Shower System

Supports multiple shower experiences through diverter selection.

Turn on water: Rotate main control knob clockwise to start flow.
Set temperature: Move temperature lever to desired setting. Wait for temperature to stabilize (approx. 10 seconds).
Select spray function: Turn diverter knob to desired position (Overhead, Handheld, Body Jets, or combinations).
Adjust handheld spray: Rotate face of handheld shower to select between 5 spray patterns.
Adjust body jets: Rotate individual nozzles to direct spray. Press nozzles to increase/decrease flow.
Use temperature memory: System remembers last temperature setting for next use.
Pause function: Turn main control knob to minimum flow to pause without losing temperature setting.
Shut off: Turn main control knob fully counterclockwise to off position.

WARNING! Do not force controls. If knob is stiff, check for mineral buildup. Never exceed maximum temperature setting.

Safety Features

Anti-Scald Protection: Mechanical stop prevents temperature exceeding 120°F (49°C). Pressure Balancing: Maintains consistent temperature during pressure fluctuations. Thermal Cut-off: If cold water fails, flow reduces to trickle. Manual Override: Emergency bypass allows full cold water flow.

Care & Cleaning

Use soft cloth and mild, non-abrasive cleaner. Do not use abrasive pads or harsh chemicals.

Daily: Wipe down with soft cloth after use to prevent water spots.
Weekly: Clean with mixture of vinegar and water (1:3 ratio) to remove mineral deposits.
Monthly: Check and clean showerhead nozzles with included pin tool to remove debris.
Annually: Inspect seals and connections. Replace battery in digital display if dim.

CAUTION! Do not use bleach, ammonia, or abrasive cleaners. Avoid getting cleaning solutions into valve mechanism.

Regulatory Information

ASSE 1016/1070: Complies with thermostatic valve performance standards. UPC Certified: Meets Uniform Plumbing Code requirements. CSA B125: Certified for Canadian installation. Low Lead Compliant: Contains less than 0.25% lead by weight. Manufactured under ISO 9001 quality standards. For support, visit www.wetelux.com or contact 1-800-555-2468.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No water flow	Main valve closed/blockage	Ensure main water supply is on; check for kinked hoses; clean inlet filters.
Temperature fluctuates	Pressure imbalance	Check pressure-balancing cartridge; ensure both supplies have adequate pressure.
Leaking from connections	Loose fittings/worn seals	Tighten connections; replace O-rings or washers with included spare parts.
Display not working	Dead battery/water in display	Replace CR2032 battery; ensure display cover seal is intact.
Weak spray from nozzles	Mineral buildup	Clean nozzles with pin tool; soak showerhead in vinegar solution.
Diverter stiff/hard to turn	Mineral deposits	Cycle diverter while running hot water; if persistent, may need cartridge replacement.
Water too hot/cold	Temperature setting/valve issue	Adjust temperature lever; check that hot and cold supplies are connected correctly.

Reset: Turn off water, remove temperature limit stop, and reinstall to factory position.

Service: 1-800-555-2468; www.wetelux.com