Wasserstein Solar Panel For Ring Video Doorbell 1 User Manual

The Wasserstein Solar Panel is a weatherproof, high-efficiency solar charging accessory designed for the Ring Video Doorbell 1. It provides continuous power to extend battery life, reduce charging frequency, and ensure your doorbell remains operational. Compatible exclusively with Ring Video Doorbell 1 (1st Generation). Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Maintenance & Care 8. Regulatory Information 9. Troubleshooting

Features at a Glance

Key components: High-efficiency monocrystalline solar panel, Weatherproof IP65-rated casing, 10ft (3m) micro-USB charging cable, Adjustable mounting bracket, Cable management clips.

Feature	Description
Solar Panel	Monocrystalline, 5W output for optimal charging
Weather Resistance	IP65 rated - dust-tight and protected against water jets
Charging Cable	10ft (3m) micro-USB, UV-resistant and durable
Mounting Bracket	Adjustable angle (0-90°) for optimal sun exposure
Cable Clips	Included for secure cable routing
Compatibility	Ring Video Doorbell 1 (1st Generation) only
Power Output	5V/1A maximum under direct sunlight
Operating Temp	-4°F to 122°F (-20°C to 50°C)
Dimensions	7.5 x 5.5 x 0.6 inches (190 x 140 x 15 mm)
Weight	1.1 lbs (0.5 kg)

Installation

Unpack and inspect contents. Ensure proper sunlight exposure location.

Choose location: Select spot with maximum daily sunlight, facing south (Northern Hemisphere) or north (Southern Hemisphere).
Mount bracket: Use included screws to secure bracket to wall/eave. Ensure sturdy surface.
Attach solar panel: Slide panel onto bracket and tighten adjustment knob.
Route cable: Use cable clips to secure micro-USB cable from panel to doorbell.
Connect to doorbell: Plug micro-USB connector into charging port on Ring Video Doorbell 1.

WARNING! Do not install near heat sources or flammable materials. Ensure cable is not pinched or damaged during installation.

First-Time Setup

After installation, verify charging operation.

Check sunlight: Ensure panel receives direct sunlight for optimal charging.
Adjust angle: Tilt panel between 30-45° for best year-round performance.
Verify connection: Ensure micro-USB is fully inserted into doorbell charging port.
Monitor battery: Check Ring app battery status - should show "Solar Charging" or increasing percentage.
Clean panel: Remove any protective film from solar panel surface.

CAUTION! Do not look directly at solar panel under bright sunlight. Use ladder safely when installing at height.

Specifications

Panel Type: Monocrystalline silicon
Maximum Power: 5W
Output Voltage: 5V DC
Output Current: Up to 1A
Cable Length: 10ft (3m) micro-USB
Weatherproof Rating: IP65
Dimensions: 7.5" x 5.5" x 0.6" (190 x 140 x 15 mm)
Weight: 1.1 lbs (0.5 kg)
Operating Temperature: -4°F to 122°F (-20°C to 50°C)
Storage Temperature: -40°F to 185°F (-40°C to 85°C)
Compatibility: Ring Video Doorbell 1 (1st Generation) only

Controls and Settings

No physical controls on solar panel. All monitoring through Ring app.

Ring App Monitoring: Battery status shows charging icon when solar panel is active. Charging indicator varies based on sunlight intensity.

Panel Adjustment: Loosen adjustment knob to change tilt angle (0-90°). Tighten knob to secure position.

Optimal Positioning: Adjust seasonally - higher angle in winter, lower in summer for your hemisphere.

Connecting Devices

Only compatible with Ring Video Doorbell 1. Not compatible with wired doorbells or other models.

Ensure Ring Doorbell 1 is properly installed and functioning.
Locate micro-USB charging port on back/side of doorbell.
Connect micro-USB cable from solar panel to doorbell.
Secure cable using included clips to prevent disconnection.
Check Ring app for charging status within 5-10 minutes.

Tip: For best results, install solar panel within 10ft of doorbell to avoid voltage drop.

Maintenance & Care

Regular cleaning ensures optimal performance.

Clean panel surface every 2-3 months with soft cloth and mild soap solution.
Remove snow, leaves, or debris that may block sunlight.
Check cable connections periodically for corrosion or damage.
Inspect mounting hardware annually for tightness.
During storms, panel is weatherproof but avoid direct hail impact.

CAUTION! Do not use abrasive cleaners or high-pressure water jets. Disconnect from doorbell before cleaning if possible.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. CE certified for European markets. RoHS compliant. Copyright © 2023 Wasserstein; all rights reserved. For support, visit www.wasserstein-home.com or contact [email protected]. 1-year limited warranty from date of purchase.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Not charging	Insufficient sunlight/connection	Reposition panel for direct sun; check cable connection at both ends.
Slow charging	Dirty panel/weak sunlight	Clean panel surface; check for shading during day.
Doorbell not recognizing	Compatibility issue	Ensure using Ring Video Doorbell 1 (1st Gen) only.
Cable damage	Weather/animal damage	Inspect cable; replace if frayed or chewed.
No power in app	App not updated	Update Ring app to latest version; restart doorbell.
Water in connector	Poor seal	Ensure micro-USB fully inserted; dry thoroughly before reconnecting.

Reset: Disconnect solar panel for 30 seconds, then reconnect. Restart Ring doorbell via app.

Service: [email protected]; www.wasserstein-home.com