V-Tac VT-ST63W Instruction Manual

The V-Tac VT-ST63W is a 63W LED Street Light designed for outdoor illumination, featuring high luminous efficacy, IP65 waterproof rating, wide operating temperature range, and durable construction. It is suitable for streets, parking lots, squares, and other public areas. Below are key sections covering safety instructions, product features, installation, wiring, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Instructions 3. Installation Guide 4. Technical Specifications 5. Wiring Diagram 6. Mounting Instructions 7. Operation & Dimming 8. Maintenance & Cleaning 9. Troubleshooting 10. Warranty Information

Features at a Glance

Key components: High-power LED chips, Aluminum alloy housing, Polycarbonate lens, Driver compartment, Mounting bracket.

Feature	Description
Power	63W LED
Luminous Flux	Up to 8400 lm
Color Temperature	3000K-6500K (adjustable models available)
IP Rating	IP65 (dust-tight and protected against water jets)
Operating Voltage	AC 100-277V / 50-60Hz
Power Factor	>0.9
Beam Angle	120°
Housing Material	Die-cast aluminum with anti-corrosion coating
Lens Material	High-transparency polycarbonate
Operating Temperature	-40°C to +50°C

Safety Instructions

Read all instructions before installation and operation.

Ensure the power is switched OFF at the mains before installation or maintenance.
Installation must be performed by a qualified electrician in accordance with local electrical codes.
Do not install near flammable materials or in explosive atmospheres.
Ensure the mounting surface can support at least 3 times the weight of the luminaire.
Do not modify the product. Use only original parts.

WARNING! Risk of electric shock. Disconnect power before servicing. Do not expose to rain or moisture during installation.

Installation Guide

Unpack and inspect contents. Verify all parts are present and undamaged.

Choose mounting location: Pole, wall, or ceiling with adequate structural support.
Assemble mounting bracket: Attach to luminaire using provided screws.
Secure bracket to mounting surface using appropriate hardware (not included).
Connect wiring: Follow wiring diagram in Section 6.
Secure luminaire to bracket and adjust tilt angle as needed.
Restore power and test operation.

CAUTION! Use appropriate personal protective equipment (PPE) during installation.

Technical Specifications

Model: VT-ST63W
Input Voltage: AC 100-277V, 50/60Hz
Power Consumption: 63W
LED Type: High-efficacy SMD LEDs
Luminous Efficacy: Up to 133 lm/W
Color Rendering Index (CRI): >70
Dimensions (LxWxH): 600mm x 210mm x 85mm
Weight: 4.2 kg
Ingress Protection: IP65
IK Rating: IK08 (impact resistance)
Warranty: 5 years

Wiring Diagram

Connect the luminaire to the mains supply via a suitable weatherproof junction box.

Identify wires: Brown (Live/L), Blue (Neutral/N), Green/Yellow (Earth/PE).
Ensure all connections are tight and insulated.
For dimmable models: Connect dimmer wires as per dimmer manufacturer's instructions (typically Purple/Violet and Grey wires).

Tip: Use conduit glands (not included) for cable entry points to maintain IP rating.

Mounting Instructions

Detailed steps for pole and wall mounting.

Pole Mounting: Use U-bracket (included). Wrap around pole, secure with bolts. Attach luminaire bracket to U-bracket.
Wall Mounting: Use wall bracket (included). Fix to wall with appropriate anchors. Attach luminaire.
Angle Adjustment: Loosen tilt adjustment bolt, set desired angle (0°-15°), retighten securely.
Ensure all bolts are tightened to recommended torque (2.5 Nm).

WARNING! Do not overtighten screws. Check stability after installation.

Operation & Dimming

Standard model operates at full brightness when powered. Dimmable models require compatible dimmer.

Switch ON/OFF via mains switch or external control system.
For dimming (if supported): Use 1-10V, DALI, or phase-cut dimmer as per model variant.
Dimming range: Typically 10%-100% of light output.
No user-serviceable parts inside. Do not open housing.

Note: Allow 2-3 minutes for full brightness after cold start in low temperatures.

Maintenance & Cleaning

Regular inspection ensures optimal performance and longevity.

Disconnect power before any maintenance.
Clean lens and housing with soft cloth and mild detergent if needed. Do not use abrasive cleaners.
Check mounting hardware for tightness annually.
Inspect seals for damage. Replace if compromised to maintain IP rating.

CAUTION! Do not use high-pressure water jets directly on seals. Do not disassemble the LED module.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Light does not turn on	No power, wiring fault	Check mains power, circuit breaker, and wiring connections.
Light flickers	Loose connection, voltage fluctuation, incompatible dimmer	Secure all connections. Check supply voltage. Use correct dimmer type.
Reduced light output	Driver failure, LED degradation, dirt on lens	Clean lens. If persists, contact service for driver/LED check.
Water inside housing	Seal damaged or improperly installed	Disconnect power. Dry unit. Replace seal or entire unit if damaged.
Overheating	Poor ventilation, ambient temperature too high	Ensure adequate airflow. Do not install in enclosed fixtures.

Reset: For smart/dimmable models, power cycle (OFF for 10 sec, then ON) may reset internal controller.

Warranty Information

V-Tac warrants this product against defects in materials and workmanship for a period of 5 years from the date of purchase. This warranty does not cover damage due to improper installation, misuse, accident, unauthorized modification, or acts of nature. For warranty service, contact your supplier or V-Tac support with proof of purchase.

Support: For technical assistance, visit www.v-tac.eu or contact [email protected].