Unique UGP-120WSPB Owner's Manual

The Unique UGP-120WSPB is a 120-watt portable power station with a 12V DC output, 5V/2.4A USB ports, AC inverter, built-in lithium battery, LCD display showing battery level and output status, overload protection, cooling fan, and multiple charging options (AC adapter, solar panel, car charger). Designed for outdoor, emergency, and mobile power needs. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging the Power Station 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Portable power station unit, AC power adapter, car charging cable, user manual. Front panel includes LCD display, power button, USB ports, DC output ports, and AC outlet.

Feature	Description
AC Inverter Output	120W pure sine wave AC outlet for small appliances
USB Output Ports	Two 5V/2.4A USB ports for charging phones/tablets
12V DC Output	For 12V devices (car vacuum, air pump, etc.)
LCD Display	Shows battery level, output status, and warnings
Power Button	Turns unit on/off and controls output
Cooling Fan	Automatically activates during high load
Overload Protection	Shuts off output if overload detected
Battery Indicator	LED lights showing remaining charge
Charging Input	For AC adapter, solar panel, or car charger
Carrying Handle	Integrated handle for portability

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect included AC adapter to charging port and wall outlet. Charge fully before first use.
Positioning: Ensure unit is in a well-ventilated area, away from heat sources and moisture.
Connecting Devices: Turn off power station before connecting any devices.
Power On: Press and hold power button for 3 seconds to turn on.

WARNING! Do not expose to water or extreme temperatures. Keep away from children.

First-Time Setup

Power on unit; observe LCD display.

Check Battery: Ensure battery is fully charged (LCD shows 100%).
Connect AC Adapter: Plug into wall outlet and charging port until full.
Test Outputs: Connect a small device (e.g., phone charger) to USB port to verify operation.
Configure Settings: Use power button to cycle through output modes if applicable.

CAUTION! Use only provided or manufacturer-approved cables and adapters.

Specifications

Model: UGP-120WSPB.
Battery Capacity: 12V/10Ah Lithium-ion.
AC Output: 120W pure sine wave, 110V/60Hz.
USB Output: 5V/2.4A per port, 2 ports total.
DC Output: 12V/10A max.
Input Charging: AC adapter (15V/2A), solar panel (12-24V), car charger (12V).
Display: LCD with battery level, output voltage/current.
Protections: Overload, short circuit, over-temperature, low battery.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: Approx. 5.5 lbs (2.5 kg).

Controls and Settings

Front Panel: Power button, LCD display, USB ports, DC output port, AC outlet.

Power Button: Press once to turn on/off; hold for 3 seconds to reset. LCD Display: Shows battery percentage, output status (AC/USB/DC), warning icons. Output Control: AC outlet turns on automatically when device plugged in; USB/DC active when power on. Battery Save Mode: Automatically enters sleep mode after 30 minutes of no load.

Connecting Devices

USB: For phones, tablets, power banks. DC: For 12V devices (using appropriate adapter). AC: For small appliances (≤120W).

Ensure power station is turned off before connecting devices.
Plug device into appropriate port (USB, DC, or AC).
Turn on power station; device should receive power.
Monitor LCD for battery level and overload warnings.

Tip: Do not exceed 120W total output across all ports.

Charging the Power Station

Supports AC wall charging, solar panel charging, and car charging.

AC Charging: Connect AC adapter to charging port and wall outlet. LCD shows charging icon.
Solar Charging: Connect compatible solar panel (12-24V) to DC input port. Ensure direct sunlight.
Car Charging: Use car charger cable plugged into vehicle's 12V outlet while engine is running.
Charging Time: Approx. 6-8 hours from empty via AC adapter.
Status: LCD displays battery percentage; charging complete at 100%.

WARNING! Use only manufacturer-approved charging accessories. Do not charge near flammable materials.

Safety Features

Overload Protection: Automatically shuts off output if load exceeds 120W. Short Circuit Protection: Cuts power if short detected. Over-Temperature Protection: Fan activates; unit may shut down if overheated. Low Battery Protection: Automatically turns off when battery drops below 10% to prevent damage.

Care & Cleaning

Turn off and unplug all devices before cleaning. Use dry, soft cloth to wipe exterior. Do not use liquids or abrasive cleaners.

CAUTION! Do not disassemble unit. Keep ports free of dust and debris.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE certified for European market. Copyright © 2025 Unique Power Solutions; trademarks of Unique Power Solutions, Inc. For support, visit www.uniquepowersolutions.com or contact 1-800-555-UGP1 (8471).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Connect to AC charger; allow to charge for 30 minutes before use.
No output from ports	Overload protection triggered	Disconnect all devices; turn unit off and on; reconnect one device at a time.
LCD display blank	Unit in sleep mode	Press power button to wake; if no response, charge battery.
Overheating	High ambient temp or overload	Move to cooler location; reduce load; ensure fan vents are unobstructed.
Slow charging	Low input power or faulty cable	Use provided AC adapter; check connections; try different wall outlet.

Reset: Hold power button for 10 seconds to force reset.

Service: 1-800-555-UGP1 (8471); www.uniquepowersolutions.com