Tradetuff Eclipse SAL24 User Manual

The Tradetuff Eclipse SAL24 is a 24-inch LED Area Light designed for commercial and industrial applications, featuring high-efficiency LED technology, durable IP65-rated construction, multiple mounting options, adjustable light output, and compatibility with standard 120-277V AC power. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Operation Modes 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-efficiency LED array, Aluminum heat sink, Polycarbonate lens, Mounting brackets, Power input terminal, Dimming control interface.

Feature	Description
LED Array	High-output SMD LEDs with 50,000-hour lifespan
IP Rating	IP65 for dust and water resistance
Mounting Options	Ceiling, wall, or pendant mounting
Dimming Capability	0-10V dimming compatible
Power Input	Universal 120-277V AC, 50/60Hz
Thermal Management	Integrated aluminum heat sink
Lens Material	Polycarbonate with anti-glare coating
Color Temperature	Selectable 3000K/4000K/5000K
Beam Angle	120° wide distribution
Operating Temp	-20°C to 40°C (-4°F to 104°F)

Installation

Unpack and inspect contents. Ensure mounting surface can support fixture weight.

Turn off power: Disconnect power at circuit breaker before installation.
Mount fixture: Use provided brackets to secure to ceiling, wall, or pendant.
Wire connections: Connect line/neutral wires to terminal block (brown/blue).
Secure lens: Attach polycarbonate lens using provided screws.
Restore power: Turn on circuit breaker after installation complete.

WARNING! Installation must be performed by qualified electrician. Ensure proper grounding.

First-Time Setup

After installation, configure light settings for optimal performance.

Select color temperature: Use DIP switches inside housing to choose 3000K/4000K/5000K.
Configure dimming: Connect 0-10V dimmer wires if dimming functionality required.
Test operation: Turn on power and verify light output.
Adjust angle: Loosen bracket screws to aim light as needed, then retighten.

CAUTION! Do not open housing while powered. Allow to cool before handling.

Specifications

Model: Eclipse SAL24
Power Consumption: 100W nominal
Luminous Flux: 12,000 lumens
Efficacy: 120 lm/W
Color Rendering Index (CRI): >80
Input Voltage: 120-277V AC, 50/60Hz
Power Factor: >0.9
Dimensions: 24" x 8" x 4" (610mm x 203mm x 102mm)
Weight: 8.8 lbs (4 kg)
Warranty: 5 years limited

Controls and Settings

Internal DIP switches control operational parameters. No external controls on fixture.

DIP Switch Settings: Located inside junction box. Switch 1: Color temperature selection (ON=3000K, OFF=4000K). Switch 2: Dimming enable/disable. Switch 3: Emergency battery backup enable (if equipped). Switch 4: Test mode.

Dimming: Connect compatible 0-10V dimmer to purple/gray wires. Dimming range 10-100%.

Thermal Protection: Automatic output reduction at high temperatures.

Connecting to Power

Universal voltage input accepts 120-277V AC.

Ensure power is OFF at circuit breaker.
Remove junction box cover.
Connect line (brown) and neutral (blue) wires to terminal block.
Connect ground wire to grounding terminal.
For dimming: Connect purple (dim+) and gray (dim-) wires to dimmer controller.
Secure all connections and replace cover.

Tip: Use wire nuts or terminal connectors rated for appropriate voltage and temperature.

Operation Modes

Normal operation: Full brightness when powered. Dimmed operation: When 0-10V dimmer connected.

Full brightness: Default operation with dimmer disconnected or at 10V.
Dimmed mode: Light output proportional to dimmer voltage (1V=10%, 10V=100%).
Thermal throttling: Automatic brightness reduction if temperature exceeds 60°C (140°F).
Emergency mode: Battery backup provides 90 minutes of reduced output during power failure (optional).

WARNING! Do not exceed maximum ambient temperature. Ensure adequate ventilation.

Safety Features

Over-temperature protection: Reduces output automatically. Short-circuit protection: Internal fuse. Surge protection: Built-in surge suppressor (5kV). IP65 rating: Protected against dust and water jets.

Care & Maintenance

Turn off power before maintenance. Clean lens with soft, dry cloth. Do not use chemicals or abrasives.

CAUTION! Do not disassemble fixture beyond removing lens for cleaning. Warranty void if tampered with.

Regulatory Information

UL Listed 1598, CSA C22.2 No. 250.0, FCC Part 15 Class B. Complies with OSHA standards. Copyright © 2025 Tradetuff Lighting. All trademarks property of Tradetuff Industries. For support, visit www.tradetufflighting.com or contact 1-800-555-2833.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No light output	Power supply	Check circuit breaker; verify voltage at fixture; ensure connections secure.
Flickering light	Loose connection/dimmer	Tighten all connections; check dimmer compatibility; replace if defective.
Reduced brightness	Overheating/dimming	Ensure adequate ventilation; check ambient temperature; verify dimmer setting.
Humming/buzzing	Driver issue	Check for loose components; ensure proper voltage; contact support if persistent.
Water in fixture	Seal compromised	Check gasket integrity; ensure lens properly sealed; replace damaged seals.

Reset: Turn power off for 30 seconds, then restore.

Service: 1-800-555-2833; www.tradetufflighting.com