Togo Power SP-100W User Manual

The Togo Power SP-100W is a 100W portable power station designed for outdoor adventures, emergency backup, and off-grid power needs. It features a high-capacity lithium battery, multiple output ports (AC, DC, USB), pure sine wave AC inverter, solar charging capability, LCD display for status monitoring, overload protection, and a compact, rugged design. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging the Power Station 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Pure Sine Wave AC Inverter, LCD Display Panel, Multiple Output Ports, Solar Charging Input, Car Charging Input.

Feature	Description
AC Output	Pure sine wave 100W output for sensitive electronics
DC Output Ports	12V/10A carport and 5.5mm DC output
USB Output Ports	Two USB-A (5V/2.4A) and one USB-C (PD 18W)
LCD Display	Shows battery level, input/output power, and warnings
Solar Charging Input	Supports up to 100W solar panel input (MC4 connector)
Car Charging Input	12V car adapter for charging on the go
AC Charging Input	Standard wall outlet charging (AC 100-240V)
Overload Protection	Automatic shutdown on overload or short circuit
Battery Management System	Protects against overcharge, over-discharge, and overheating
LED Flashlight	Built-in emergency light with SOS mode

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect the included AC adapter to the AC INPUT port and a wall outlet. Charge fully before first use.
Solar Panel Connection: Connect compatible solar panel to SOLAR INPUT port using MC4 connector (sold separately).
Car Charging: Plug the 12V car charger into the DC INPUT port and vehicle's 12V outlet.
Device Connection: Connect your devices to appropriate output ports.

WARNING! Keep away from water, heat sources, and direct sunlight. Do not disassemble.

First-Time Setup

Power on the unit; monitor LCD display.

Initial Charge: Charge to 100% using AC adapter (approx. 6-7 hours).
Power On: Press and hold POWER button for 3 seconds to turn on.
Output Selection: Press OUTPUT button to cycle through AC, DC, and USB outputs.
LCD Settings: Use SETTINGS button to adjust screen brightness and timeout.

CAUTION! Use only provided or recommended cables and adapters.

Specifications

Battery Capacity: 100Wh (Lithium-ion).
AC Output: 100W Pure Sine Wave, 110V/60Hz.
DC Output: 12V/10A (Car Port), 12V/5A (DC5521).
USB Output: USB-A: 5V/2.4A (x2), USB-C: 5V/3A, 9V/2A, 12V/1.5A (18W Max).
Input: Solar: 12-24V/100W Max, AC: 100-240V/50-60Hz, Car: 12V/8A.
Display: LCD with battery level, input/output wattage, temperature.
Flashlight: 3 modes (High, Low, SOS).
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 2.2 lbs (1 kg).

Controls and Settings

Access functions via front panel buttons. Front Panel: POWER, OUTPUT, SETTINGS, FLASHLIGHT.

LCD Display: Shows battery percentage, input/output power, estimated runtime, temperature, and error codes.

Output Control: Press OUTPUT to enable/disable AC, DC, or USB ports individually. Settings: Press SETTINGS to adjust LCD brightness (3 levels) and screen timeout (30s/1min/Always On). Flashlight: Press FLASHLIGHT to cycle through High, Low, SOS, and Off modes.

Connecting Devices

AC Devices: Plug into AC outlet (max 100W). DC Devices: Use car port or DC5521 port. USB Devices: Connect to USB-A or USB-C ports.

Check device power requirements (watts/volts/amps).
Ensure total connected load does not exceed 100W.
Turn on power station before connecting devices.
Select appropriate output mode if needed.

Tip: For sensitive electronics (laptops, medical devices), use pure sine wave AC output.

Charging the Power Station

Supports AC wall charging, solar charging, and car charging.

AC Charging: Connect AC adapter to INPUT port and wall outlet. LCD shows charging status.
Solar Charging: Connect solar panel to SOLAR INPUT. Ensure panel is in direct sunlight.
Car Charging: Plug car charger into DC INPUT and vehicle's 12V outlet (engine running recommended).
Charging Time: AC: ~6-7 hours, Solar: ~8-10 hours (with 100W panel), Car: ~8-9 hours.
Battery Protection: Unit automatically stops charging at 100%.

WARNING! Use only Togo Power approved solar panels and cables. Do not charge in extreme temperatures.

Safety Features

Overload Protection: Automatically shuts off output if exceeds 100W. Short Circuit Protection: Cuts power on short circuit. Temperature Control: Reduces output or shuts down if overheated. Low Voltage Protection: Turns off when battery drops below 10% to prevent damage.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; do not use liquids. Recharge every 3 months if storing long-term.

CAUTION! Do not expose to rain or moisture. Avoid dropping or impacting the unit.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2025 Togo Power; trademarks of Togo Power Inc. For support, visit www.togopower.com or contact 1-800-555-TOGO.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery depleted/unit off	Charge battery; press and hold POWER button for 3 seconds.
Overload shutdown	Connected devices exceed 100W	Disconnect devices; reduce total load; restart unit.
Not charging	Faulty cable/power source	Check connections; try different outlet/cable; ensure solar panel has sunlight.
LCD display blank	Screen timeout/battery dead	Press any button to wake; charge if battery is empty.
Device not charging via USB	Incompatible device/cable	Use original device cable; ensure USB port is enabled via OUTPUT button.

Reset: Hold POWER + OUTPUT for 10 seconds to reset system.

Service: 1-800-555-TOGO; www.togopower.com