Superior Electronics SUPPSW001 Instructions Manual

The Superior Electronics SUPPSW001 is a premium-grade power supply unit designed for high-performance computing and sensitive electronic equipment. It features universal input voltage (100-240V AC), active PFC, multiple DC output rails with over-voltage/current/short-circuit protection, modular cable management, silent fan operation with zero-RPM mode, and 80 Plus Platinum efficiency certification. Below are key sections for safety, features, installation, configuration, operation, and maintenance.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Connections 6. Connecting to System 7. Operation & Monitoring 8. Protection Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-efficiency transformer, modular cable ports, cooling fan, AC input socket, DC output connectors, power switch, and monitoring LED.

Feature	Description
AC Input Socket	For universal mains power connection (100-240V)
Modular DC Ports	For connecting motherboard, CPU, PCIe, SATA, and peripheral cables
Power Switch	Main power on/off rocker switch
Status LED	Indicates operational status and fault conditions
Cooling Fan	120mm silent fan with hybrid zero-RPM mode
Over-Voltage Protection (OVP)	Automatically shuts down if voltage exceeds safe limits
Over-Current Protection (OCP)	Protects against excessive current draw
Short-Circuit Protection (SCP)	Immediate shutdown on detected short circuit
Over-Temperature Protection (OTP)	Prevents damage from overheating
Active PFC	Power Factor Correction for efficiency and stability

Installation

Unpack and inspect contents. Ensure compatible with your system case and components.

Prepare the case: Turn off and unplug the system. Open the computer case.
Mount the PSU: Align the unit with the mounting bracket in the case and secure with provided screws.
Connect modular cables: Attach required cables (24-pin ATX, 8-pin EPS, PCIe, etc.) to the PSU ports.
Route cables: Neatly route cables to corresponding motherboard and component connectors.
Connect AC power cord: Plug the IEC cable into the PSU input socket and wall outlet.

WARNING! Ensure the system is completely powered off and unplugged before installation. Use anti-static precautions.

First-Time Setup

After physical installation, configure and test the power supply.

Initial power check: Flip the rear power switch to ON. The status LED should illuminate steady green.
System boot: Press the system power button. Verify all components receive power and the fan spins up.
Monitor voltages: Enter system BIOS/UEFI to check that all voltage rails (3.3V, 5V, 12V) are within specification.
Fan mode selection: Use the dedicated button (if equipped) or software to select Silent, Standard, or Performance fan profile.

CAUTION! Do not force connectors. Ensure all connections are fully seated and secure.

Specifications

Model: SUPPSW001
Input Voltage: 100-240V AC, 50/60Hz (Auto-ranging)
Efficiency: 80 Plus Platinum (≥92% typical load)
Maximum Power: 850W Continuous
DC Output Rails: +3.3V@25A, +5V@25A, +12V@70A, [email protected], +5VSB@3A
Connectors: 1x 24-pin ATX, 2x 8-pin (4+4) EPS, 4x 8-pin (6+2) PCIe, 8x SATA, 4x Peripheral
Cooling: 120mm Fluid Dynamic Bearing Fan
Protections: OVP, OCP, SCP, OTP, OPP (Over Power), UVP (Under Voltage)
Operating Temperature: 0°C to 50°C
Dimensions: Standard ATX (150mm x 86mm x 160mm)

Controls and Connections

Rear Panel: AC Input, Power Switch. Front/Side: Modular DC ports, Fan Mode Button, Status LED.

Modular Ports: Labeled MB (24-pin), CPU (8-pin), PCIe (8-pin), SATA/PERIPHERAL. Status LED: Green (Normal), Red (Fault/Protection Triggered), Off (No AC Power). Fan Button: Cycles through Silent (fan off at low load), Standard, Performance modes.

Connecting to System

Match cables to components and PSU ports.

Motherboard: Connect the 24-pin ATX cable and the 8-pin EPS CPU power cable(s).
Graphics Card: Connect the required number of 6+2 pin PCIe cables.
Storage Drives: Connect SATA power cables to SSDs/HDDs.
Peripherals: Use 4-pin Molex or SATA cables for fans, pumps, or other devices.

Tip: Use only the cables provided with this PSU. Do not mix cables from other power supplies.

Operation & Monitoring

Designed for continuous, stable operation.

Normal Operation: The status LED is green. The fan operates based on load and selected mode.
Load Monitoring: Keep total system power draw below 850W for optimal efficiency and longevity.
Fan Behavior: In Silent mode, the fan may remain off until a temperature or load threshold is reached.
Fault Indication: A red status LED indicates a protection circuit has been triggered. Refer to Troubleshooting.

WARNING! Do not cover ventilation intakes/exhausts. Ensure adequate airflow around the unit.

Protection Features

Automatic safeguards to protect the PSU and connected components.

OVP/OCP/SCP/OTP: The unit will automatically shut down and require a full AC power cycle (switch off, unplug, wait 30 seconds) to reset. OPP: Prevents operation beyond maximum rated power. UVP: Guards against unstable low voltage conditions.

Care & Maintenance

Unplug from AC power before any maintenance. Periodically clean the fan intake grill with compressed air to prevent dust buildup.

CAUTION! Do not open the PSU casing. No user-serviceable parts inside. Void warranty if opened.

Regulatory Information

FCC Part 15 Class B: Complies with limits for digital devices. CE, cTUVus, TÜV, CB Scheme certified. RoHS and WEEE compliant. Copyright © 2025 Superior Electronics; all trademarks are property of their respective owners. For technical support, visit www.superiorelectronics.com/support or contact 1-800-555-0199.

Troubleshooting

Symptom	Possible Cause	Corrective Action
System does not power on	PSU switch off / faulty connection	Ensure rear switch is ON. Re-seat 24-pin and CPU power cables. Test outlet.
Red Status LED lit	Protection circuit triggered	Unplug from AC, wait 30 sec, replug. If persists, disconnect all components and test with minimal load.
Fan is very loud or not spinning	High load / Fan mode / Obstruction	Check system load. Cycle fan mode button. Ensure fan intake is clear of dust/debris.
System randomly shuts down	Overheating / Overload / Faulty rail	Check PSU and system temperatures. Verify total power draw is within 850W limit.
No power to specific components	Loose cable / Faulty cable	Re-seat the cable at both PSU and component ends. Try a different modular cable from the kit.

Reset: Full AC power cycle (unplug, wait, replug).

Service: 1-800-555-0199; www.superiorelectronics.com/support