Suaoki 100W Solar Panel User Manual

The Suaoki 100W Solar Panel is a high-efficiency, portable monocrystalline solar panel designed for charging 12V batteries, power stations, and compatible devices. It features a compact foldable design, high conversion efficiency, durable ETFE material, built-in kickstand, multiple output ports (DC5521, Anderson, USB), and integrated charge controller for overcharge protection. Ideal for camping, RV trips, emergency power, and off-grid applications. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Connections 6. Connecting Devices 7. Charging Operation 8. Safety Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Monocrystalline solar cells, foldable design with carrying handle, integrated charge controller, output ports (DC5521, Anderson, USB), built-in kickstand, and durable ETFE laminate.

Feature	Description
Solar Cells	High-efficiency monocrystalline silicon
Rated Power	100W maximum output
Output Ports	DC5521 (12V), Anderson connector, USB-A (5V)
Charge Controller	Built-in for overcharge, short-circuit, and reverse polarity protection
Kickstand	Adjustable for optimal sun angle
Material	ETFE laminate for durability and water resistance
Foldable Design	Compact for portability with carrying handle
Operating Voltage	12V nominal (18V open circuit)
Weight	Approximately 4.4 lbs (2 kg)
Dimensions (Open)	41 x 21 inches (104 x 53 cm)

Installation

Unpack and inspect contents. Ensure all components are present.

Choose Location: Place panel in direct sunlight, away from shadows.
Unfold Panel: Lay panel flat on ground or mount using grommets (optional).
Adjust Kickstand: Set angle towards the sun (approx. 30-45 degrees).
Connect to Device: Use appropriate cable from panel to battery/power station.
Secure Cables: Use included cable ties to prevent tripping.

WARNING! Do not install near heat sources or flammable materials. Ensure panel is stable to avoid wind damage.

First-Time Setup

Position panel for optimal sunlight; connect to device.

Unfold panel fully and extend kickstand.
Connect panel to battery/power station using included cables (match polarity).
Check connection: LED on charge controller should light up.
Monitor charging: Device should indicate charging status.
Adjust angle every few hours for maximum sun exposure.

CAUTION! Avoid touching panel surface when hot. Keep away from children and pets.

Specifications

Maximum Power: 100W.
Open Circuit Voltage (Voc): 18V.
Short Circuit Current (Isc): 5.7A.
Cell Type: Monocrystalline silicon.
Efficiency: Up to 23.5%.
Output Ports: DC5521 (12V/8.3A max), Anderson (12V/8.3A max), USB-A (5V/2.4A).
Protection: Overcharge, short-circuit, reverse polarity.
Operating Temperature: -4°F to 149°F (-20°C to 65°C).
Water Resistance: IP65 (splash proof).
Warranty: 12 months limited.

Controls and Connections

Charge Controller: LED indicator (green = charging, red = fault). Output Ports: DC5521, Anderson, USB-A.

LED Indicators: Green light = normal operation; Red light = error (check connections).

Kickstand: Adjustable for optimal sun angle. Grommets: For permanent mounting (optional). Cables: Included DC5521 to alligator clips, Anderson to Anderson, USB cable.

Connecting Devices

Connect to 12V batteries, power stations, or USB devices.

12V Battery: Use DC5521 to alligator clips (red to positive, black to negative).
Power Station: Use Anderson to Anderson cable (match ports).
USB Devices: Plug directly into USB-A port.
Check Polarity: Ensure correct +/- connections to avoid damage.

Tip: Disconnect panel from device when not in use to prevent overcharging.

Charging Operation

Charges 12V batteries and compatible power stations.

Position panel in direct sunlight (avoid shading).
Connect cables securely to device.
Monitor LED: Green light indicates charging.
Check device display for charging progress.
Disconnect when battery is full or when not in use.
Fold panel after use and store in dry place.

WARNING! Do not attempt to charge non-12V batteries. Do not exceed maximum current ratings.

Safety Features

Built-in charge controller prevents overcharging, short-circuit, and reverse polarity. IP65 rating for water resistance. ETFE laminate protects against UV degradation.

Care & Cleaning

Disconnect from all devices before cleaning. Wipe surface with soft, damp cloth. Do not use abrasive cleaners.

CAUTION! Do not spray water directly on ports. Store in dry, cool place when not in use.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2025 Suaoki; trademarks of Suaoki Inc. For support, visit www.suaoki.com or contact [email protected].

Troubleshooting

Symptom	Possible Cause	Corrective Action
No output (LED off)	No sunlight/connections	Move to direct sun; check all cable connections.
Red LED on controller	Reverse polarity/short circuit	Disconnect and check polarity; ensure no short circuits.
Low charging current	Shading/angle/dirty panel	Remove shadows; adjust angle; clean panel surface.
USB port not working	Device not compatible/overload	Use compatible device; do not exceed 2.4A.
Panel hot to touch	Normal operation in sun	Allow to cool; avoid touching during peak sun.

Reset: Disconnect all cables for 5 minutes, then reconnect.

Service: [email protected]; www.suaoki.com