Somfy Oximo WireFree Solar Panel Installation Manual

The Somfy Oximo WireFree Solar Panel is a photovoltaic accessory designed to power Somfy Oximo WireFree motorized systems for blinds, shades, and awnings. It provides sustainable, maintenance-free operation by converting sunlight into electrical energy, eliminating the need for battery replacement or hardwired electrical connections. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: High-efficiency monocrystalline solar panel, Weatherproof housing, Mounting bracket with adjustable angle, Integrated power cable with Oximo connector, Charge status indicator LED.

Installation

Unpack and inspect contents. Ensure all parts are present and undamaged.

1. Choose Location: Select a south-facing location (Northern Hemisphere) with maximum daily sunlight exposure, free from shadows.
2. Mount Bracket: Secure the mounting bracket to a stable surface (wall, roof, railing) using appropriate screws and anchors.
3. Attach Panel: Slide the solar panel onto the bracket and tighten the adjustment knobs.
4. Angle Adjustment: Adjust the panel angle according to your latitude (typically 15-45 degrees) for optimal performance.
5. Route Cable: Route the integrated power cable to the Oximo motor location, securing it with cable clips.
6. Connect to Motor: Plug the cable connector into the solar input port on the Oximo WireFree motor.

WARNING! Do not install near potential sources of shading (trees, chimneys). Ensure mounting surface can support panel weight. Do not drill into the panel itself.

First-Time Setup

After physical installation, verify system operation.

1. Initial Charge: Allow the panel to charge the motor's internal battery for a full 24 hours in direct sunlight before first use.
2. Status Check: Observe the LED indicator on the solar panel or motor (consult motor manual). Solid green typically indicates charging/charged.
3. Motor Pairing: If installing with a new motor, follow the Oximo motor manual to pair the remote control.
4. Test Operation: Use the paired remote to test the motor's open/close function. The system should operate smoothly.

CAUTION! Do not disconnect the solar panel while the motor is in operation. Ensure all connections are dry before powering.

Specifications

• Model: Somfy Oximo WireFree Solar Panel.
• Cell Type: Monocrystalline Silicon.
• Maximum Power (Pmax): 10W.
• Open Circuit Voltage (Voc): 21V.
• Short Circuit Current (Isc): 0.6A.
• Output Connector: Proprietary Oximo plug.
• Cable Length: 5 meters (16.4 feet).
• Ingress Protection: IP65 (Dust tight, protected against water jets).
• Expected Charge Time: 1-2 full sun days to charge a depleted battery.
• Compatible Motors: All Somfy Oximo WireFree series motors (check specific model compatibility).

Controls and Settings

The solar panel itself has no user controls. System management is done through the connected Oximo motor and its remote.

Status LED Indication (Typical):

• Solid Green: Battery is charging or fully charged.
• Flashing Green: Charging in progress under low light.
• Flashing Red/Orange: Fault detected (e.g., poor connection, shading).
• Off: No sunlight or not connected.

Motor Settings (via Remote): Adjust open/close limits, speed, and automation sun/wind settings which affect energy consumption and charging needs.

Connecting Devices

The solar panel connects directly only to the Somfy Oximo WireFree motor.

1. Ensure both the motor and solar panel are in the off or disconnected state.
2. Locate the weatherproof solar input port on the Oximo motor housing.
3. Align the connector key and firmly push the solar panel cable plug into the port until it clicks.
4. Secure the cable along its route to prevent strain on the connection.

Tip: For best results, keep the cable run as short and direct as possible. Do not use extensions or modify the cable.

Operation & Maintenance

The system is designed for autonomous operation.

1. Automatic Charging: The panel charges whenever sunlight is available. The motor's intelligent circuit manages battery health.
2. Seasonal Adjustment: It is recommended to adjust the panel tilt angle seasonally for optimal winter/sunmer sun capture.
3. Snow/Ice: The panel is designed to shed snow. Gently remove heavy snow accumulation if necessary.
4. Performance Monitoring: Regular operation of the motor is the best indicator. Sluggish operation may indicate insufficient charging.

WARNING! Do not attempt to open or repair the solar panel. There are no user-serviceable parts inside. Do not walk on the panel.

Accessibility Features

The solar panel enables a fully wire-free installation, improving accessibility by removing the need for proximity to power outlets or complex wiring. The motor can be operated via standard Somfy remote controls, including wall switches and Telis® RTS handheld remotes.

Care & Cleaning

Periodic cleaning maintains efficiency.

1. Disconnect the cable from the motor (optional but recommended).
2. Use a soft, damp cloth with mild soap and water to wipe the glass surface.
3. Rinse with clean water and dry with a soft, lint-free cloth.
4. Remove leaves, pollen, or bird droppings promptly.

CAUTION! Do not use abrasive materials, harsh chemicals, or high-pressure water jets. Do not clean when the panel is hot to avoid thermal shock.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. CE marked according to applicable EU directives. RoHS compliant. Waste Electrical and Electronic Equipment (WEEE): Do not dispose of with household waste. Recycle according to local regulations. For support, visit www.somfy.com or contact your local Somfy dealer.

Troubleshooting

Reset: Disconnect solar panel for 30 seconds, then reconnect. Perform a motor reset per its manual if needed.

Service: Contact authorized Somfy dealer or visit www.somfy.com/support.