Rollease Acmeda AUTOMATE Solar Panel 2.0 Manual

The Rollease Acmeda AUTOMATE Solar Panel 2.0 is a high-efficiency solar power accessory designed to provide sustainable, off-grid energy for AUTOMATE motorized window covering systems. It features advanced photovoltaic cells, weather-resistant construction, integrated charge controller, battery management, and compatibility with the AUTOMATE ecosystem. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Indicators 6. Connecting to AUTOMATE System 7. Operation & Power Management 8. Maintenance & Cleaning 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-efficiency monocrystalline solar panel, Charge controller unit, Weatherproof junction box, Mounting brackets, Status LED indicators, Power output cable.

Feature	Description
Solar Panel	Monocrystalline cells with high conversion efficiency
Charge Controller	Integrated MPPT for optimal power harvesting
Weather Resistance	IP65 rated for outdoor use
Battery Management	Protects connected battery from overcharge/discharge
Status Indicators	LEDs for power, charging, and fault conditions
Mounting System	Adjustable brackets for optimal sun angle
Output Cable	Weatherproof connector for AUTOMATE hub
Compatibility	Designed for AUTOMATE motors and hubs
Dimensions	Compact design for discreet installation
Warranty	10-year performance warranty

Installation

Unpack and inspect contents. Choose optimal location for sunlight exposure.

Select mounting location: South-facing (Northern Hemisphere) with minimal shading.
Mount brackets: Secure to roof, wall, or ground using provided hardware.
Attach solar panel: Secure panel to brackets using mounting clamps.
Route cables: Run output cable to AUTOMATE hub location, securing with clips.
Connect to hub: Plug weatherproof connector into SOLAR INPUT port on hub.

WARNING! Install only in dry conditions. Ensure mounting surface can support panel weight. Follow local electrical codes.

First-Time Setup

After installation, configure system for optimal performance.

Check connections: Ensure all cables are securely connected.
Verify sunlight: Panel should receive direct sunlight for charging.
Hub recognition: AUTOMATE hub should detect solar panel automatically.
Monitor status: Check LED indicators (green = normal operation).
Configure settings: Use AUTOMATE app to set power management preferences.

CAUTION! Do not disconnect cables under load. Keep panel surface clean for maximum efficiency.

Specifications

Panel Type: Monocrystalline silicon.
Maximum Power: 50W.
Open Circuit Voltage: 21.6V.
Short Circuit Current: 2.9A.
Operating Temperature: -40°C to +85°C.
Dimensions: 670 x 540 x 30 mm.
Weight: 4.5 kg.
Protection Rating: IP65 (dust and water resistant).
Controller: MPPT with overcharge/discharge protection.
Compatibility: AUTOMATE Series 2 hubs and motors.
Warranty: 10 years product, 25 years performance.

Controls and Indicators

Status is indicated via LED lights on the junction box.

LED Indicators:

Green Solid: Normal operation, charging battery
Green Flashing: Charging in progress
Yellow Solid: Battery fully charged
Red Solid: Fault condition (check connections)
Red Flashing: Over-temperature or over-voltage
No Light: No power (check sunlight and connections)

AUTOMATE App Integration: Monitor solar input, battery level, and energy savings through the AUTOMATE mobile application.

Connecting to AUTOMATE System

Compatible with AUTOMATE Series 2 hubs and compatible motors.

Ensure AUTOMATE hub is powered off before connection.
Locate SOLAR INPUT port on AUTOMATE hub.
Connect weatherproof cable from solar panel to hub.
Power on AUTOMATE hub.
Verify connection in AUTOMATE app under Power Settings.

Tip: For multiple panels, consult Rollease Acmeda for parallel connection guidelines.

Operation & Power Management

The solar panel operates automatically when exposed to sunlight.

Daily Operation: Panel charges connected battery during daylight hours.
Power Priority: System uses solar power first, then battery backup.
Battery Protection: Controller prevents overcharging and deep discharge.
Weather Adaptation: Performance adjusts automatically to light conditions.
Monitoring: Track performance through AUTOMATE app energy reports.
Sleep Mode: During extended darkness, system enters low-power mode.

WARNING! Do not attempt to service internal components. Contact qualified technician for repairs.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

Cleaning: Use soft cloth and mild detergent with water. Clean every 3-6 months.
Inspection: Check for physical damage, loose connections, or debris quarterly.
Snow/Ice: Remove carefully with soft brush; do not use sharp tools.
Connection Check: Ensure cables and connectors remain secure and weatherproof.

CAUTION! Do not use abrasive cleaners or high-pressure water. Disconnect from system before cleaning if possible.

Regulatory Information

CE Certified: Complies with European safety standards. RoHS Compliant: Free of hazardous substances. FCC Part 15: Class B digital device. This product contains components protected by intellectual property rights. For support, visit www.rolleaseacmeda.com or contact your local Rollease Acmeda representative.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Insufficient sunlight or shading	Relocate panel to sunnier location; remove obstructions.
Red LED indicator	Fault condition	Check all connections; restart system; contact support if persistent.
Battery not charging	Controller fault or battery issue	Verify battery health; check controller connections.
Reduced performance	Dirty panel or aging cells	Clean panel surface; monitor performance over time.
Not detected by hub	Connection or compatibility issue	Ensure proper connection to SOLAR INPUT port; verify hub compatibility.
Water ingress	Damaged seals or casing	Disconnect immediately; contact support for replacement.

Reset: Disconnect from hub for 30 seconds, then reconnect.

Service: Contact Rollease Acmeda support or authorized service center. Do not attempt internal repairs.