Reolink Solar Panel Plus Quick Start Manual

The Reolink Solar Panel Plus is a high-efficiency solar charging accessory designed to provide continuous, renewable power for compatible Reolink security cameras. It features weatherproof construction, adjustable mounting, and smart charging technology to maximize solar energy harvesting. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Package Contents 3. Installation 4. Specifications 5. Positioning & Angle Adjustment 6. Connecting to Camera 7. Charging Status Indicators 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-efficiency monocrystalline solar panel, Weatherproof cable and connector, Adjustable mounting bracket, Smart charging circuit with overcharge protection.

Feature	Description
High-Efficiency Cells	Monocrystalline silicon for optimal energy conversion
Weatherproof Design	IP65 rated for outdoor use in various conditions
Adjustable Bracket	Allows optimal angle adjustment for sun exposure
Smart Charging	Auto-regulates voltage/current to protect camera battery
Universal Compatibility	Designed for specific Reolink Argus, Go, or E1 series cameras
Long Cable	Extended cable for flexible placement relative to camera
LED Indicator	Shows charging status (solid/flashing patterns)
Easy Mounting	Includes screws and anchors for wall/roof installation
Corrosion-Resistant	Materials withstand rain, snow, and UV exposure
Plug-and-Play	Simple connection to camera's charging port

Package Contents

Unpack and verify all items are present.

Reolink Solar Panel Plus unit
Adjustable mounting bracket
Mounting screws and wall anchors
Weatherproof cable (length varies by model)
Quick Start Guide (this manual)

WARNING! Do not discard packaging until all components are verified. Contact support if any item is missing or damaged.

Installation

Choose location with maximum direct sunlight exposure.

Select mounting surface: Wall, roof, pole, or other stable outdoor structure.
Attach bracket: Use provided screws and anchors; ensure tight and secure fit.
Adjust angle: Loosen bracket knob, tilt panel toward sun (typically 30-45 degrees), retighten.
Route cable: Run cable to camera location, avoiding sharp bends or pinches.
Connect to camera: Plug weatherproof connector into camera's solar/power input port.

CAUTION! Install only in safe, accessible locations. Avoid areas with heavy shade or potential obstructions.

Specifications

Panel Type: Monocrystalline silicon.
Max Power Output: Varies by model (e.g., 5W, 6W).
Weatherproof Rating: IP65.
Operating Temperature: -20°C to 60°C (-4°F to 140°F).
Cable Length: Typically 3m (10ft) or as specified.
Connector: Proprietary weatherproof plug.
Compatibility: Specific Reolink battery-powered cameras.
Mounting: Adjustable bracket with 180° tilt range.
Dimensions: Varies by model (approx. 260mm x 180mm x 25mm).
Weight: Approx. 0.8kg (1.76lbs).

Positioning & Angle Adjustment

Optimal performance requires correct orientation to the sun.

Northern Hemisphere: Face panel south. Southern Hemisphere: Face panel north.

Adjust tilt angle seasonally: - Summer: 15-20 degrees from horizontal. - Spring/Autumn: 30-45 degrees. - Winter: 50-60 degrees (to capture lower sun).

Ensure no shadows from trees, buildings, or other objects during peak sun hours (10am-4pm).

Connecting to Camera

Compatible cameras have a dedicated solar input port.

Ensure camera is powered off or in low-power mode.
Locate solar/power input port on camera (refer to camera manual).
Align connector correctly; plug in firmly until it clicks or seats fully.
Secure weatherproof seal (if applicable) to prevent moisture ingress.
Power on camera. Charging should begin automatically in daylight.

Tip: Connection is typically one-way; incorrect orientation will not fit. Do not force.

Charging Status Indicators

LED behavior indicates charging state (location varies by model).

LED State	Meaning
Solid Green	Charging normally (adequate sunlight)
Flashing Green	Charging but sunlight is weak/fluctuating
Off (No light)	No sunlight (night) or no connection to camera
Flashing Red	Fault detected (check connection, compatibility)

Note: Some models may not have an LED; check camera battery level via Reolink app instead.

Maintenance & Care

Periodic cleaning ensures maximum efficiency.

Unplug from camera before cleaning (optional but recommended).
Wipe panel surface with soft, damp cloth to remove dust, pollen, bird droppings.
Use mild soap solution if needed; rinse with clean water. Do not use abrasive cleaners.
Inspect cable and connector for damage, wear, or loose connections annually.
Check mounting hardware tightness seasonally, especially after storms.

CAUTION! Do not use high-pressure water sprays. Do not disassemble panel.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. CE/RoHS: Complies with European directives. Waste Electrical: Dispose of in accordance with local regulations. Copyright © Reolink. For support, visit support.reolink.com or contact your regional Reolink support center.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Camera battery not charging	Insufficient sunlight, poor angle, shade	Reposition panel for direct sun; adjust angle; remove obstructions.
LED not lighting	No sun, faulty connection, incompatible camera	Check sunlight; reconnect cable; verify compatibility.
Charging intermittent	Cloudy weather, dirty panel, loose cable	Clean panel; secure connections; normal in low-light conditions.
Camera not recognizing panel	Wrong port, damaged cable, camera fault	Use correct solar input port; inspect cable; restart camera.
Water inside connector	Seal not properly closed	Dry thoroughly, ensure seal is fully engaged before reconnecting.

Reset: Disconnect panel from camera for 30 seconds, then reconnect.

Service: support.reolink.com; refer to regional contact information on website.