Reolink Solar Panel 2 Operational Instruction

The Reolink Solar Panel 2 is a high-efficiency, weatherproof solar charging solution designed to power compatible Reolink security cameras and devices. It features a monocrystalline silicon panel for optimal energy conversion, an integrated charge controller, adjustable mounting bracket, and waterproof connectors. This guide covers safety, features, installation, setup, operation, maintenance, and troubleshooting for continuous, renewable power supply.

Features at a Glance

Key components: Monocrystalline Solar Panel, Integrated Charge Controller, Adjustable Mounting Bracket, Waterproof DC Connector, Cable Management Clips.

Installation

Unpack and inspect contents. Choose location with maximum sunlight exposure.

1. Select mounting location: Ensure direct sunlight for 6-8 hours daily, facing south (Northern Hemisphere) or north (Southern Hemisphere).
2. Mount bracket: Use provided screws and anchors to secure bracket to wall, pole, or roof.
3. Attach solar panel: Secure panel to bracket; adjust tilt angle for optimal sun exposure (typically 15-45 degrees).
4. Route cable: Use cable clips to secure cable along mounting surface; avoid sharp bends or pinching.
5. Connect to device: Ensure device is powered off; connect waterproof DC connector to device's solar input port.

WARNING! Do not install near flammable materials or where falling could cause injury. Ensure mounting surface is stable and secure.

First-Time Setup

After installation, verify proper operation.

1. Check connections: Ensure all connections are secure and weatherproof seals are intact.
2. Verify sunlight: Panel should be in direct sunlight without shading from trees or structures.
3. Monitor indicator: LED should show charging status (e.g., red for charging, green for full/standby).
4. Check device: Power on connected camera/device; verify it indicates solar charging in app/interface.
5. Optimize angle: Adjust panel tilt seasonally for best performance (steeper in winter, shallower in summer).

CAUTION! Do not disconnect under load. Keep connectors dry and free from debris.

Specifications

• Panel Type: Monocrystalline Silicon.
• Maximum Power Output: Typically 5W, 6W, or 9W depending on model.
• Open Circuit Voltage (Voc): Varies by model (e.g., 12V nominal).
• Controller Type: Integrated MPPT or PWM charge controller.
• Output Connector: Weatherproof DC plug (specific to Reolink devices).
• Cable Length: Varies (commonly 5m/16.4ft or 10m/32.8ft).
• Weatherproof Rating: IP65 or higher (dust-tight and protected against water jets).
• Operating Temperature: Typically -20°C to 60°C (-4°F to 140°F).
• Dimensions & Weight: Varies by model; compact and lightweight design.
• Compatibility: Specific Reolink Argus, Go, or other battery-powered cameras.

Controls and Connections

Primary interface through physical connections and status LED.

Panel/Bracket: Adjustable tilt mechanism, mounting holes. Connector: DC output plug with weatherproof seal. Indicator: LED shows charging status (red=charging, green=full/standby, off=no power).

No user controls on panel itself; charging parameters managed by integrated controller. Device settings (if any) accessible via connected camera's app for solar charging status and battery level.

Connecting to Devices

Compatible with specific Reolink wireless/battery cameras.

1. Ensure device compatibility: Check model number against Reolink compatibility list.
2. Power off device: Before connecting solar panel to avoid electrical issues.
3. Connect cable: Plug DC connector into device's solar input port until it clicks/seals.
4. Secure cable: Use clips to prevent strain on connection point.
5. Power on device: Device should recognize solar input; check app for charging status.

Tip: For best results, ensure device battery has some charge before relying solely on solar.

Operation and Monitoring

Designed for autonomous operation with minimal intervention.

1. Daily operation: Panel automatically converts sunlight to power; controller regulates charging.
2. Status monitoring: Check LED indicator (red=charging, green=full/standby).
3. App monitoring: Use Reolink app to view device battery level and solar charging status.
4. Seasonal adjustment: Change panel tilt angle every few months for optimal sun exposure.
5. Performance factors: Output varies with sunlight intensity, weather, season, and panel angle.
6. Battery maintenance: Solar panel helps maintain battery charge; may not fully recharge deeply depleted batteries quickly in low light.

WARNING! Do not attempt to disassemble panel or controller. No user-serviceable parts inside.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Cleaning: Periodically clean panel surface with soft cloth and mild soapy water to remove dust, dirt, bird droppings.
2. Inspection: Check for physical damage, loose connections, or cable wear every 3-6 months.
3. Snow/leaves: Remove snow, leaves, or debris that may shade the panel.
4. Connector care: Ensure connector and port remain clean, dry, and free from corrosion.

CAUTION! Do not use abrasive materials or harsh chemicals. Disconnect from device before cleaning if possible.

Regulatory Information

Complies with relevant electrical and safety standards. CE, RoHS, and other certifications as applicable. Copyright and trademarks owned by Reolink. For technical support, warranty, or product information, visit www.reolink.com or contact support through the app. Disposal should follow local electronic waste regulations.

Troubleshooting

Reset: Disconnect from device for 1 minute, then reconnect. Restart connected device.

Service: Contact Reolink Support for non-user-serviceable issues. Do not open the panel.