Redarc SPMB0001 Quick Start Manual

The Redarc SPMB0001 is a high-performance battery management system designed for reliable power management in demanding environments. This quick start guide covers essential safety information, installation steps, basic operation, and initial configuration to get your system running quickly and safely.

1. Safety Information 2. Package Contents 3. Installation Overview 4. Wiring Connections 5. Initial Setup & Configuration 6. Basic Operation 7. LED Status Indicators 8. Specifications 9. Troubleshooting 10. Warranty & Support

Safety Information

Read all safety instructions before installation or operation. Failure to follow these instructions may result in electric shock, fire, or equipment damage.

Warning	Description
Electrical Safety	Disconnect all power sources before installation or maintenance
Battery Connection	Ensure correct polarity when connecting batteries
Environmental	Install in well-ventilated area away from heat sources
Mounting	Secure unit firmly to prevent vibration damage
Cable Management	Use appropriate cable sizes and protect from abrasion

Package Contents

Verify all components are present before beginning installation.

Redarc SPMB0001 Battery Management Unit (1)
Mounting brackets and hardware kit
Connection cables with terminals
Quick Start Manual (this document)
Warranty registration card

WARNING! Do not install if any components are damaged or missing. Contact your supplier immediately.

Installation Overview

Follow these steps for proper installation.

Choose mounting location: Dry, ventilated area with adequate clearance.
Mount unit: Use provided brackets and hardware.
Prepare cables: Cut to appropriate lengths, strip ends, crimp terminals.
Connect power sources: Follow wiring diagram carefully.
Connect load devices: Ensure proper current ratings.
Secure all connections: Tighten terminals to specified torque.

CAUTION! Ensure all connections are secure and insulated before applying power.

Wiring Connections

Battery Input: Connect to primary battery bank (positive/negative).
Auxiliary Input: Optional secondary power source connection.
Load Outputs: Protected outputs for connected devices.
Communication Port: For system monitoring and configuration.
Ground Connection: Essential for safety and proper operation.
Sensor Inputs: Temperature and voltage monitoring connections.

Initial Setup & Configuration

Configure basic settings before first use.

Power On Sequence: 1. Verify all connections. 2. Apply power to input. 3. Check LED indicators. 4. Configure via interface if required.

Basic Configuration: Battery type selection (AGM, Gel, Lithium), Charge voltage settings, Load management preferences, Protection thresholds, Communication setup.

Basic Operation

Normal operating procedures for daily use.

Power On: Unit initializes automatically when power is applied.
Status Check: Verify LED indicators show normal operation.
Load Connection: Connect devices to appropriate output terminals.
Monitoring: Observe system performance during operation.
Shutdown: Disconnect loads before turning off power source.

Tip: Regular monitoring ensures optimal performance and early fault detection.

LED Status Indicators

Understand what each LED indicator means.

Power LED (Green): Solid = Normal operation, Flashing = Standby mode.
Charge Status (Yellow): Solid = Charging, Flashing = Bulk charge.
Fault Indicator (Red): Solid = Warning condition, Flashing = Fault detected.
Load Active (Blue): Indicates connected load is drawing power.
Communication (White): Activity on communication port.

WARNING! Red fault indicator requires immediate attention. Disconnect loads and investigate cause.

Specifications

Technical specifications for the SPMB0001 unit.

Parameter	Specification
Input Voltage Range	10-32V DC
Maximum Continuous Current	100A
Peak Current Capacity	150A (30 seconds)
Operating Temperature	-20°C to +60°C
Storage Temperature	-30°C to +85°C
Protection Features	Over-current, Over-voltage, Under-voltage, Over-temperature
Communication Interface	CAN Bus, RS232
Dimensions (LxWxH)	150 x 100 x 50 mm
Weight	850g
Ingress Protection	IP65

Troubleshooting

Common issues and solutions.

Symptom	Possible Cause	Corrective Action
No power LED	No input power	Check input connections and voltage
Red fault LED	Over-current condition	Disconnect loads, reset unit, reconnect gradually
Unit not charging	Battery voltage too low	Check battery condition and connections
Communication failure	Cable or configuration issue	Verify cable integrity and communication settings
Overheating	Insufficient ventilation	Improve airflow around unit

Reset Procedure: Disconnect all power for 30 seconds, then reconnect.

Warranty & Support

Redarc SPMB0001 comes with a 3-year limited warranty covering defects in materials and workmanship. Warranty does not cover damage from improper installation, misuse, or unauthorized modifications.

For technical support: Email [email protected] or call +61 8 8322 4848. Visit www.redarc.com.au for manuals, software updates, and additional resources.

CAUTION! Installation by qualified personnel is recommended. User assumes all responsibility for proper installation and operation.