Pyle PWR95S User Manual

The Pyle PWR95S is a high-performance 95-watt power inverter designed for automotive and marine applications, converting 12V DC battery power to 120V AC household power. It features pure sine wave output, overload protection, low battery alarm, cooling fan, remote control capability, multiple AC outlets, and USB charging ports. Ideal for powering sensitive electronics, tools, and appliances on the go. Below are key sections for safety, features, installation, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Indicators 6. Connecting Devices 7. Operation Modes 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Pure sine wave inverter, Remote control panel, Battery cables, Cooling fan, AC outlets, USB ports, LED indicators.

Feature	Description
Pure Sine Wave Output	Clean power for sensitive electronics
Power Rating	95 watts continuous power output
Input Voltage	12V DC from vehicle/marine battery
Output Voltage	120V AC, 60Hz
USB Ports	5V DC for charging mobile devices
Remote Control	Wireless on/off and monitoring
Overload Protection	Automatic shutdown on overload
Low Battery Alarm	Audible warning when battery voltage drops
Cooling Fan	Thermally controlled for temperature management
LED Indicators	Power, fault, and battery status

Installation

Unpack and inspect contents. Ensure proper ventilation.

Choose location: Mount in dry, well-ventilated area away from heat sources.
Connect to battery: Attach red cable to positive (+) terminal, black to negative (-) terminal.
Secure connections: Tighten all terminals to prevent arcing.
Ground connection: Connect grounding wire to vehicle chassis if required.
Connect remote: Plug remote control cable into inverter port.

WARNING! Ensure battery polarity is correct to avoid damage. Disconnect battery before installation.

First-Time Setup

Power on inverter; verify operation.

Check battery voltage: Ensure battery reads 11-15V DC before connection.
Power switch: Turn inverter to ON position.
LED verification: Green power LED should illuminate.
Test output: Plug in low-wattage device to confirm operation.
Remote setup: Pair remote control if included.

CAUTION! Do not exceed 95-watt continuous load. Allow adequate airflow around unit.

Specifications

Model: Pyle PWR95S.
Continuous Power: 95 watts.
Peak Power: 190 watts.
Input Voltage: 12V DC.
Output Voltage: 120V AC ±5%.
Output Frequency: 60Hz ±0.5%.
Waveform: Pure sine wave.
Efficiency: >85%.
USB Output: 5V DC, 2.1A max.
Protections: Overload, short circuit, over-temperature, low battery.
Operating Temp: -4°F to 140°F (-20°C to 60°C).

Controls and Indicators

Front Panel: POWER switch, LED indicators, AC outlets, USB ports. Remote: ON/OFF, status display.

LED Indicators: Green (power on), Red (overload/fault), Yellow (low battery).

Controls: Power switch (ON/OFF), remote enable button, fan speed control (auto). Display: Remote shows input voltage, output wattage, error codes. Settings: Low voltage cutoff adjustable via DIP switches (10.5V/11V/11.5V).

Connecting Devices

AC devices: Plug into outlets. USB devices: Connect to USB ports.

Check device wattage: Ensure total load ≤ 95 watts continuous.
Power sequence: Turn on inverter before connecting devices.
Connect devices: Plug into AC outlets or USB ports.
Monitor: Watch LED indicators for normal operation.

Tip: Start with highest-wattage device first to test load capacity.

Operation Modes

Supports continuous, standby, and remote operation.

Normal mode: Powers connected devices continuously up to 95W.
Standby mode: Auto-enters when no load detected (reduces power consumption).
Remote mode: Use wireless remote to turn on/off from distance.
Eco mode: Optional setting to minimize idle current draw.
Fan operation: Automatically activates based on temperature.

WARNING! Do not cover ventilation slots. Allow fan to operate freely.

Safety Features

Overload Protection: Auto-shutdown if load exceeds 95W. Low Battery Cutoff: Prevents battery drain below set voltage. Short Circuit Protection: Immediate shutdown on short. Over-Temperature: Thermal protection activates at 158°F (70°C). Reverse Polarity: Fuse protection against incorrect connections.

Care & Maintenance

Keep unit clean and dry. Check connections periodically.

Cleaning: Use dry cloth; do not use liquids.
Ventilation: Ensure air vents are unobstructed.
Battery check: Monitor battery voltage regularly.
Connection inspection: Tighten terminals every 3 months.

CAUTION! Disconnect from battery before cleaning. Store in dry location.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. ETL listed to UL 458 standards. Copyright © 2025 Pyle Audio; trademarks of Pyle USA. For support, visit www.pyleaudio.com or contact 1-800-555-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery/low voltage	Check battery connections; ensure voltage >11V; reset inverter.
Overload shutdown	Exceeded wattage limit	Reduce connected load; wait 5 minutes; restart.
Fan not running	Thermal conditions	Fan runs only when hot; ensure ambient temperature <140°F.
Low battery alarm	Battery voltage low	Recharge battery; check alternator/charging system.
Remote not working	Battery/range	Replace remote batteries; ensure within 30 ft range.

Reset: Disconnect from battery for 30 seconds, then reconnect.

Service: 1-800-555-1234; www.pyleaudio.com