Powerness SolarX S80 User Manual

The Powerness SolarX S80 is a high-efficiency 80W portable solar panel designed for outdoor and emergency power needs. It features monocrystalline solar cells, a durable waterproof casing, integrated USB-A and USB-C outputs, a built-in kickstand, and a carrying handle. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Monocrystalline solar panel, USB-A output port, USB-C PD output port, LED power indicator, Integrated kickstand, Carrying handle, Weather-resistant casing.

Installation

Unpack and inspect contents. Choose optimal location for sunlight exposure.

1. Position the panel: Place on stable surface or use kickstand to angle toward the sun.
2. Ensure clear exposure: Remove any obstructions like shadows or debris from panel surface.
3. Connect devices: Use appropriate cables to connect devices to USB-A or USB-C ports.
4. Activate power: Press POWER button to enable output ports.

WARNING! Do not look directly at the sun when positioning panel. Avoid placing in areas where it may be tripped over or damaged.

First-Time Setup

Position panel and connect your first device.

1. Initial placement: Set up in direct sunlight during peak hours (10am-2pm) for best results.
2. Connect device: Use manufacturer-approved cable to connect phone or tablet to USB port.
3. Check indicator: LED should illuminate showing power is being generated and delivered.
4. Monitor charging: Verify your device begins charging within 30 seconds of connection.

CAUTION! Ensure the panel surface is clean and free of obstructions before first use. Do not expose to extreme temperatures beyond operating range.

Specifications

• Maximum Power: 80W
• Cell Type: Monocrystalline Silicon
• USB-A Output: 5V/2.4A (12W Max)
• USB-C PD Output: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A (60W Max)
• Open Circuit Voltage: 21.6V
• Short Circuit Current: 4.8A
• Dimensions: 26.8 x 19.9 x 1.2 inches (folded)
• Weight: 8.8 lbs
• Operating Temperature: -4°F to 140°F (-20°C to 60°C)
• Weather Resistance: IP65 (Dust tight, protected against water jets)

Controls and Settings

Simple interface with minimal controls for ease of use.

Front Panel: POWER button, LED indicator (Green: Normal operation, Red: Overload/Error), USB-A port, USB-C PD port.

Operation: Press POWER once to activate outputs, press again to deactivate. LED indicates status: Solid green = power flowing, Flashing green = low sunlight/charging, Solid red = overload/fault, Off = no power/no sunlight.

Positioning: Adjust kickstand to achieve optimal 45-90 degree angle toward sun. Use built-in compass markings for orientation if available.

Connecting Devices

Compatible with most USB-charged devices including phones, tablets, power banks, and small electronics.

1. Check device compatibility: Ensure your device supports USB or USB-PD charging.
2. Select appropriate port: Use USB-C PD for fast-charging compatible devices, USB-A for standard charging.
3. Use quality cables: Always use manufacturer-recommended cables for best performance and safety.
4. Monitor connection: LED indicator will confirm power is being delivered to connected device.

Tip: For fastest charging, connect only one device at a time to maximize power delivery to that device.

Charging & Power Management

Optimizing performance for different conditions.

1. Ideal conditions: Direct sunlight, clear skies, panel angled perpendicular to sun's rays.
2. Partial sun: Charging will occur but at reduced rate. LED may flash green indicating lower power.
3. Cloudy days: Expect 25-50% of rated output depending on cloud density.
4. Multiple devices: Can charge two devices simultaneously but total output limited to 80W combined.
5. Power management: Panel automatically adjusts output based on sunlight availability and device requirements.
6. Efficiency tips: Clean panel surface regularly, reposition every 2-3 hours to follow sun, avoid shadows.

WARNING! Do not attempt to modify or repair the panel yourself. Discontinue use if casing is damaged or compromised.

Safety Features

Built-in protections: Over-current protection, Over-voltage protection, Short-circuit protection, Reverse polarity protection, Over-temperature protection.

Automatic shutdown in fault conditions. Weather-resistant design prevents water ingress in normal use conditions.

Care & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Cleaning: Use soft, damp cloth with mild soap solution if needed. Dry completely before use.
2. Storage: Store in cool, dry place when not in use. Avoid prolonged exposure to extreme temperatures.
3. Transport: Use carrying handle. Ensure ports are protected from debris during transport.
4. Inspection: Regularly check for cracks, discoloration, or damage to panel surface or casing.

CAUTION! Never use abrasive cleaners, solvents, or high-pressure water on the panel. Do not submerge in water despite IP65 rating.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. CE certified for European market. RoHS compliant. Copyright © 2023 Powerness Solar; all trademarks property of Powerness Solar Technologies, Inc. For support, visit www.powernesssolar.com or contact 1-800-555- SOLAR (76527).

Troubleshooting

Reset: Disconnect all devices, press and hold POWER button for 10 seconds to reset electronics.

Service: 1-800-555-SOLAR; www.powernesssolar.com/support