Powereco PE-LTK-3x35W Manual

The Powereco PE-LTK-3x35W is a high-efficiency LED tube light conversion kit designed to replace traditional fluorescent fixtures. It features three 35W LED tubes, universal voltage input (100-277V AC), high lumen output, energy-saving design, instant start, flicker-free operation, high color rendering index (CRI >80), IP20 rating, and a lifespan of up to 50,000 hours. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Three 35W LED tubes, Driver/Power Supply, Mounting brackets, Wiring connectors, End caps.

Installation

Unpack and inspect contents. Ensure power is disconnected before installation.

1. Remove existing fluorescent tubes and ballast: Turn off power, remove old tubes, disconnect or bypass ballast as per instructions.
2. Mount brackets: Secure mounting brackets to ceiling or fixture base using provided screws.
3. Connect wiring: Use quick-connect terminals to link driver input to AC power lines (L, N, GND).
4. Install LED tubes: Insert tubes into sockets and rotate 90 degrees to lock in place.
5. Restore power and test.

WARNING! Installation must be performed by a qualified electrician. Ensure all connections are secure and insulated.

First-Time Setup

After installation, restore power and verify operation.

1. Power verification: Ensure AC power matches input range (100-277V).
2. Initial test: Switch on power; all three tubes should light instantly at full brightness.
3. Check for flicker: Observe for any flickering or dimming issues.
4. Secure mounting: Verify all tubes are firmly seated and brackets are tight.

CAUTION! Do not touch LED tubes during operation due to heat. Allow to cool before handling.

Specifications

• Model: PE-LTK-3x35W
• Input Voltage: 100-277V AC, 50/60Hz
• Power Consumption: 105W total (3x35W)
• Luminous Flux: 12,600 lm total (4,200 lm per tube)
• Color Temperature: 4000K (Cool White) / 5000K (Daylight) options
• CRI: >80
• Beam Angle: 120 degrees
• Power Factor: >0.9
• Operating Temperature: -20°C to 40°C
• Ingress Protection: IP20
• Lifespan: Up to 50,000 hours
• Dimensions: 1200mm length per tube

Controls and Settings

This is a fixed-output LED kit with no user controls. Operation is via standard wall switch.

Note: No dimming capability unless specified with compatible dimmer (optional).

Installation Settings: Ensure correct voltage range, proper wiring polarity, and secure mechanical mounting.

Connecting to Power

Connect to standard AC mains power through appropriate switch.

1. Turn off main power at circuit breaker.
2. Identify wires: Line (L), Neutral (N), Ground (GND).
3. Connect driver input terminals: L to live, N to neutral, GND to ground.
4. Secure all connections with wire nuts or terminal blocks.
5. Restore power and test with switch.

Tip: Use a voltage tester to confirm power is off before working on connections.

Operation Modes

Single operation mode: Full brightness when powered.

1. Normal operation: Switch on for instant full illumination.
2. No warm-up: Immediate maximum output.
3. Consistent output: Maintains stable brightness throughout lifespan.
4. Thermal protection: Automatic reduction if overheating detected.

WARNING! Do not operate in enclosed fixtures not rated for LED tubes. Ensure adequate ventilation.

Safety Features

Over-temperature protection: Reduces output if overheating. Short-circuit protection: Built-in circuit protection. Surge protection: Withstands voltage spikes up to 4kV.

Care & Maintenance

Turn off power before cleaning. Use dry or slightly damp cloth; no harsh chemicals.

CAUTION! Do not spray liquids directly on tubes or driver. Allow to cool before cleaning.

Regulatory Information

Complies with UL/cUL, CE, RoHS, and Energy Star standards. Copyright © 2025 Powereco; trademarks of Powereco Lighting Solutions. For support, visit www.powerecolighting.com or contact 1-800-555-2837.

Troubleshooting

Reset: Turn power off for 30 seconds, then restore.

Service: 1-800-555-2837; www.powerecolighting.com