Powereco PE-120C User Manual

The Powereco PE-120C is a 120-watt portable power station designed for emergency backup, outdoor activities, and off-grid power needs. It features a high-capacity lithium-ion battery, multiple output ports (AC, DC, USB), pure sine wave inverter technology, LCD display for monitoring, solar charging capability, and built-in safety protections. Powered by 100-240V AC input or 12V car/DC input. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging the Unit 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Pure Sine Wave Inverter, LCD Display Panel, Multiple Output Ports, Solar Charging Input, Car Charging Cable.

Feature	Description
AC Output Ports	2 x 120V AC outlets (pure sine wave)
DC Output Ports	1 x 12V/10A car port; 2 x 5.5mm DC ports
USB Ports	2 x USB-A (5V/2.4A); 1 x USB-C (PD 18W)
LCD Display	Shows battery level, input/output wattage, estimated runtime
AC Input	100-240V AC for wall charging
DC/Solar Input	12-24V DC for car or solar panel charging
POWER Button	Turns unit on/off
DC Button	Activates DC output ports
AC Button	Activates AC inverter output
LED Light	Built-in emergency flashlight with SOS mode

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect included AC adapter to wall outlet and unit's AC input port.
Connect devices: Use appropriate cables for AC, DC, or USB devices.
For solar charging: Connect compatible solar panel (12-24V) to DC input port.
For car charging: Use included car charger cable in vehicle's 12V outlet.

WARNING! Keep away from water and extreme temperatures. Do not disassemble unit.

First-Time Setup

Power on unit; check LCD display.

Fully charge battery: Connect to AC power until display shows 100%.
Configure settings: Press and hold SETUP button to access brightness, auto-off timer.
Test outputs: Connect a small device to verify each output port functions.
Monitor display: Familiarize yourself with battery level and wattage readings.

CAUTION! First charge may take 6-8 hours. Use only included or approved cables.

Specifications

Battery Capacity: 120Wh (33,000mAh/3.7V).
Inverter Output: 120V AC, 60Hz, 120W continuous (240W surge).
DC Output: 12V/10A max.
USB Output: USB-A: 5V/2.4A each; USB-C: 5V/3A, 9V/2A, 12V/1.5A.
Input: AC: 100-240V, 50/60Hz; DC/Solar: 12-24V, 8A max.
Display: LCD with battery percentage, input/output power, time remaining.
Charging Time: AC: 6-8 hours; Solar: 8-10 hours (with 60W panel).
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 3.3 lbs (1.5 kg).

Controls and Settings

Access functions via front panel buttons. Front Panel: POWER, AC, DC, LED, SETUP.

LCD Display: Shows battery percentage, input/output wattage, estimated runtime, temperature warning.

Settings Menu (hold SETUP 3 sec): LCD brightness (Low/Med/High), Auto-off timer (1/2/4/8 hrs), Battery save mode (On/Off). Safety: Overload protection, short circuit protection, over-temperature protection, low-voltage cutoff. Charging: AC priority, solar charging indicator, battery health status.

Connecting Devices

AC Devices: Plug into AC outlets (max 120W total). DC Devices: Use car port or DC ports. USB Devices: Connect phones, tablets, etc.

Turn on unit with POWER button.
Press AC button to activate AC outlets (beep confirms).
Press DC button to activate DC and USB ports.
Connect device; check LCD for load wattage.

Tip: Start with low-power devices first to test. Do not exceed 120W total output.

Charging the Unit

Supports AC wall charging, car charging, and solar charging.

AC Charging: Use included adapter; plug into wall and AC input port.
Car Charging: Use car charger cable in vehicle's 12V outlet while engine is running.
Solar Charging: Connect compatible solar panel (12-24V, 8A max) to DC input port.
Monitoring: LCD shows charging status, input wattage, and estimated time to full.
Battery Save: Enable in settings to extend battery life by limiting charge to 80%.

WARNING! Use only approved solar panels. Do not charge in temperatures below 32°F or above 104°F.

Safety Features

Overload Protection: Automatically shuts off output if exceeds 120W. Short Circuit Protection: Cuts power if short detected. Temperature Control: Reduces output if overheated. Low Voltage Cutoff: Turns off when battery drops below 10% to prevent damage.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; do not use liquids. Recharge every 3 months if storing long-term.

CAUTION! Do not expose to rain or moisture. Avoid dropping or puncturing battery.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2023 Powereco; trademarks of Powereco Technologies Ltd. Lithium-ion battery: Contains hazardous materials; dispose of properly according to local regulations. For support, visit www.powereco.com or contact 1-800-555-1200.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Connect to AC power for 30 minutes; then try power button.
No output from AC ports	Overload/overheat	Reduce connected load; allow to cool; press AC button again.
Slow charging	Low input power	Ensure proper AC connection; try different wall outlet; check solar panel alignment.
LCD display blank	Sleep mode/battery	Press any button to wake; if still blank, recharge unit fully.
Device not charging via USB	Cable/port issue	Try different cable; ensure USB port is activated (DC button on).

Reset: Hold POWER + SETUP for 10 seconds to reset all settings.

Service: 1-800-555-1200; www.powereco.com/support