Pontec PondoSolar Lily Island Operating Instructions Manual

The Pontec PondoSolar Lily Island is a solar-powered floating fountain and pond aerator designed for garden ponds and small water features. It features a high-efficiency solar panel, a floating island with integrated LED lights, a submersible water pump, and an adjustable fountain nozzle. The system operates automatically in daylight, creating water movement and aeration to improve pond health. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Maintenance & Cleaning 7. Winter Storage 8. Safety Information 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Floating Solar Island, High-Efficiency Solar Panel, Submersible Pump, Adjustable Fountain Nozzle, Integrated LED Lights (optional model), Suction Cup Base, and Power Cable.

Feature	Description
Solar Panel	Monocrystalline panel for automatic daylight operation
Floating Island	Lightweight, UV-resistant plastic housing
Water Pump	Submersible, low-voltage pump for fountain and aeration
Fountain Nozzle	Adjustable spray pattern (jet or bell)
LED Lights	Integrated energy-saving lights for night effect (on light-equipped models)
Suction Cup	For optional fixed placement on pond floor
ON/OFF Switch	Manual power control (on some models)
Cable Management	Waterproof cable and connector

Installation

Unpack and inspect all parts. Choose a sunny location in your pond.

Position the Solar Island: Place the floating unit on the pond surface in full sunlight.
Connect the Pump: Ensure the pump is fully submerged and not resting on the bottom debris.
Adjust the Nozzle: Turn the fountain head to achieve desired water pattern.
Optional Fixed Placement: Use the suction cup to attach the pump to a clean, flat surface on the pond floor if desired.
Ensure the solar panel cable is free of knots and fully extended towards the sun.

WARNING! Do not install in water deeper than the maximum cable length. Ensure the pump is never run dry.

First-Time Setup

The unit operates automatically when exposed to sunlight. No electrical outlet is needed.

Initial Test: Place the entire unit in a bucket of water in direct sunlight to verify operation.
Pond Placement: Float the island in your pond. The pump will start automatically when the solar panel receives sufficient light.
Nozzle Adjustment: Fine-tune the fountain spray for optimal height and pattern.
Light Operation (if equipped): LED lights will automatically turn on at dusk if the model includes this feature.

CAUTION! Handle the solar panel with care. Avoid shading from plants or structures for maximum performance.

Specifications

Power Source: Integrated 2.5W Monocrystalline Solar Panel.
Pump Output: 80-120 L/H (varies with sunlight intensity).
Operating Voltage: 5V DC (low voltage, safe for pond life).
Fountain Height: Adjustable up to 40 cm.
Cable Length: 2 meters (solar panel to pump).
LED Lights: 4 x Energy-saving LEDs (on select models).
Material: ABS Plastic (island), Stainless Steel & Plastic (nozzle).
Recommended Pond Size: Up to 5000 liters.
Weather Resistance: IP68 rated pump, UV-resistant floating island.

Controls and Operation

The system is fully automatic. The primary control is sunlight exposure.

Automatic Operation: Pump starts when solar panel receives sufficient light; stops at dusk or in shade. LED lights (if equipped) activate automatically at low light levels.

Manual Adjustment: Fountain Nozzle: Rotate to change spray pattern from a single jet to a wider bell shape. Pump Position: Adjust depth or use suction cup for fixed placement to alter water agitation. Floating Island: Can be tethered to a specific location with the included cord (if provided).

Maintenance & Cleaning

Regular maintenance ensures optimal performance and longevity.

Weekly: Check for debris on the pump intake and solar panel. Gently wipe the solar panel with a soft, damp cloth.
Monthly: Remove the pump from the water. Clean the impeller and intake filter by rinsing with clean water. Do not use chemicals.
Seasonal: Inspect all cables and connections for wear or damage.

Tip: Clean the pump more frequently in ponds with high algae or debris.

Winter Storage

To prevent frost damage, remove the unit from the pond before freezing temperatures.

Disconnect: Remove the entire unit from the pond.
Clean: Thoroughly clean the pump and island as described in Section 7. Allow all parts to dry completely.
Store: Place in its original box or a protective bag. Store in a cool, dry place away from direct sunlight.

WARNING! Never allow water to freeze inside the pump, as this will cause permanent damage.

Safety Information

This is a low-voltage solar product designed for outdoor water use.

Always operate in water. Never run the pump dry.
The solar panel is not a toy. Do not allow children to play with it.
Use only in freshwater garden ponds. Not for use in swimming pools, saltwater, or with chemicals.
Disconnect or remove from pond before performing any maintenance.
Do not attempt to open or repair the solar panel or pump housing.

Regulatory Information

This device complies with relevant low-voltage and RoHS directives. The solar panel is designed for outdoor use. Pontec and PondoSolar are trademarks. For support, spare parts, or more information, please visit the official Pontec website or contact your local dealer.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Pump does not start	Insufficient sunlight / Shade	Move unit to a sunnier location. Ensure solar panel is clean and facing the sun.
Weak fountain spray	Clogged intake / Low sun	Clean pump filter and impeller. Check for midday sun exposure.
LED lights not working	Faulty connection / Dusk sensor	Ensure cable is fully connected. Lights only operate in very low light.
Floating island tips over	Pump not centered / Wind	Adjust pump position under the island. Tether the island if provided.
Intermittent operation	Cloud cover / Cable issue	Normal behavior with passing clouds. Check cable for damage or loose connections.

Service: For persistent issues, contact customer service. Do not disassemble the sealed solar unit or pump.