Pni IP792 User Manual

The Pni IP792 is a high-performance industrial-grade IP camera designed for professional surveillance applications. It features advanced H.265 video compression, 4K Ultra HD resolution, wide dynamic range (WDR), infrared night vision up to 30 meters, IP67 weatherproof rating, PoE (Power over Ethernet) support, built-in microphone, SD card slot for local storage, and intelligent motion detection. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: 4K CMOS sensor, IR-cut filter, built-in microphone, Ethernet port, SD card slot, reset button, mounting bracket.

Feature	Description
4K Ultra HD Resolution	3840 x 2160 pixels for crystal clear video
H.265/H.264 Compression	Advanced compression for efficient bandwidth usage
Infrared Night Vision	Up to 30 meters with automatic IR-cut filter
Wide Dynamic Range (WDR)	Balances light and dark areas for clear images
PoE (802.3af)	Single Ethernet cable for power and data
IP67 Rating	Dustproof and waterproof for outdoor use
Built-in Microphone	Audio recording capability
SD Card Slot	Supports up to 256GB for local storage
Motion Detection	Intelligent alerts with customizable zones
ONVIF Conformance	Compatible with third-party NVR systems

Installation

Unpack and inspect contents. Choose appropriate mounting location.

1. Mount camera: Use included bracket and screws to secure to wall or ceiling.
2. Connect Ethernet: Run Cat5e/Cat6 cable from camera to PoE switch or injector.
3. Power connection: Use PoE or optional 12V DC power adapter.
4. Weatherproof connections: Ensure all cable glands are properly sealed.

WARNING! Install at safe height; ensure mounting surface can support camera weight. Use proper cable management.

First-Time Setup

Power on camera; access web interface for initial configuration.

1. Find camera IP: Use Pni Device Manager software or check router DHCP client list.
2. Access web interface: Enter IP address in browser (default: admin/admin).
3. Set network parameters: Configure static IP or DHCP as needed.
4. Adjust video settings: Set resolution, frame rate, compression type.
5. Configure storage: Set up SD card recording or network storage.

CAUTION! Change default password immediately. Ensure proper network security settings.

Specifications

• Image Sensor: 1/2.8" 4K CMOS.
• Resolution: 3840x2160 (4K) at 25 fps.
• Lens: 4mm fixed lens (2.8mm/6mm optional).
• Night Vision: 30m IR distance with 6 IR LEDs.
• Video Compression: H.265/H.264/MJPEG.
• Network Interface: 10/100 Mbps Ethernet, PoE (802.3af).
• Audio: Built-in microphone, line-in support.
• Storage: Micro SD card slot (up to 256GB).
• Power: PoE (802.3af) or 12V DC, 1A.
• Operating Temperature: -30°C to 60°C (-22°F to 140°F).
• Protection: IP67 weatherproof rating.

Controls and Settings

Access settings via web interface or mobile app. Physical controls: Reset button, SD card slot.

Web Interface: Video settings, network configuration, storage management, event settings, system maintenance.

Video: Resolution, frame rate, bitrate, WDR, brightness, contrast, saturation. Network: IP address, port, protocol, QoS. Storage: SD card format, recording schedule, overwrite settings. Events: Motion detection zones, sensitivity, alert actions. System: User management, firmware upgrade, reboot, factory reset.

Connecting Devices

Network: Ethernet to PoE switch. Storage: SD card insertion. Audio: External microphone input.

1. Ensure camera is powered off before making connections.
2. Insert SD card: Push until click (label facing outward).
3. Connect Ethernet: Use weatherproof connector for outdoor installations.
4. Connect audio: Optional external microphone to line-in port.

Tip: Use shielded Ethernet cables for installations near electrical interference.

Network Configuration

Supports multiple network protocols and streaming methods.

1. IP Configuration: Set static IP or use DHCP.
2. Port Forwarding: Configure router for remote access.
3. Streaming: RTSP, HTTP, ONVIF profiles available.
4. Multiple Streams: Primary and secondary streams with different settings.
5. QoS: Set priority for video traffic.
6. DDNS: Configure dynamic DNS for changing IP addresses.
7. Email Alerts: Set up SMTP for motion detection notifications.
8. FTP Upload: Configure automatic upload of event recordings.

WARNING! Change default ports for security. Use strong passwords for all accounts.

Security Features

User Authentication: Multi-level user accounts with permission settings. Data Encryption: HTTPS support for secure web access. Privacy Masking: Block sensitive areas from recording. Watermark: Digital watermark for video authentication.

Care & Maintenance

Regular cleaning of lens and housing. Check cable connections periodically.

CAUTION! Use only soft, dry cloth for lens cleaning. Do not use chemicals or abrasive materials. Check weatherproof seals annually.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE: Conforms to European safety standards. RoHS: Compliant with restriction of hazardous substances. IP67: Certified dust and water protection. For support, visit www.pnisystems.com or contact 1-800-555-7920.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No video image	Power/network issues	Check PoE connection; verify network cable; restart camera.
Poor night vision	Obstructions/settings	Clean lens; check IR LED status; adjust night mode settings.
SD card not recognized	Format/compatibility	Format card in camera; ensure compatible card type (Class 10+).
Cannot access web interface	IP address/network	Verify IP address; check firewall settings; reset to factory defaults.
Motion detection not working	Zone configuration	Check sensitivity settings; verify detection zones are enabled.

Reset: Press reset button for 10 seconds to restore factory defaults.

Service: 1-800-555-7920; www.pnisystems.com