Pni Green House 370W Manual

The Pni Green House 370W is a high-performance 370-watt grow light system designed for indoor horticulture, featuring full-spectrum LED technology, adjustable light intensity, daisy-chain connectivity, built-in cooling fans, waterproof rating (IP65), remote control, timer functionality, and energy-efficient operation. Suitable for various growth stages from seedling to flowering. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: LED light panel with full-spectrum diodes, Remote Control, Power input, Daisy-chain ports, Cooling fans, Hanging hooks, Control panel.

Installation

Unpack and inspect contents. Ensure mounting surface can support weight.

1. Mount light: Use hanging hooks; secure to ceiling or rack with included hardware.
2. Connect power: Plug AC cord into grounded outlet.
3. Daisy-chain multiple units: Connect output port of first unit to input of next using provided cable.
4. Position light: Adjust height according to plant stage (see recommendations).

WARNING! Unit is heavy; use two people for installation. Ensure secure mounting to prevent falls.

First-Time Setup

Power on light; follow initial configuration.

1. Pair remote: Point remote at receiver; press POWER and MODE simultaneously for 3 seconds.
2. Set timer: Use TIMER button to program daily on/off schedule.
3. Adjust spectrum: Select mode (VEG, BLOOM, FULL) for plant stage.
4. Calibrate intensity: Start at 50% for seedlings; increase gradually.

CAUTION! Keep light at recommended distance from plants to prevent light burn.

Specifications

• Power: 370 watts LED.
• Spectrum: Full-spectrum 380-780nm.
• Coverage: Up to 4'x4' at 24" height.
• Input Voltage: 100-240V AC, 50/60Hz.
• Daisy-chain: Up to 10 units.
• Cooling: Dual ball-bearing fans.
• Timer: 24-hour programmable.
• Dimensions: 24" x 24" x 3".
• Weight: 15.4 lbs.
• Operating Temp: 32°F to 104°F.

Controls and Settings

Access functions via control panel or remote. Control Panel: POWER, MODE, INTENSITY UP/DOWN.

Remote: POWER, VEG, BLOOM, FULL SPECTRUM, TIMER, INTENSITY +/-, DAISY-CHAIN SYNC.

Modes: VEG (blue-heavy), BLOOM (red-heavy), FULL (balanced). Intensity: Adjustable 0-100% in 10% increments. Timer: Set start/stop times for automatic operation. Daisy-chain: Master unit controls slave units when synced.

Connecting Devices

Daisy-chain: Connect units in series. Remote: Infrared line-of-sight required.

1. Turn off all units before connecting.
2. Use provided cables for daisy-chain connections.
3. Designate master unit; sync others via remote.

Tip: Ensure all connections are secure and cables are not pinched.

Operating Modes

Supports three primary modes for different growth stages.

1. VEG mode: Emphasizes blue spectrum (400-500nm) for vegetative growth.
2. BLOOM mode: Emphasizes red spectrum (620-780nm) for flowering.
3. FULL SPECTRUM: Balanced light for all stages.
4. Manual adjustment: Use intensity control to fine-tune brightness.
5. Timer operation: Set schedule for consistent light cycles.
6. Daisy-chain operation: Control multiple units from one remote.

WARNING! Do not look directly at LEDs at close range. Use protective eyewear if servicing.

Safety Features

Overheat protection: Auto-shutdown at 158°F. Waterproof: IP65 rating for splashes. Surge protection: Built-in for power fluctuations. Cooling: Fans auto-adjust based on temperature.

Care & Maintenance

Unplug before cleaning. Wipe housing with dry cloth; clean LED surface with soft, dry brush.

CAUTION! Do not use water or cleaning solutions on electrical components. Check fans regularly for dust buildup.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. ETL listed for safety standards. Copyright © 2025 Pni Green House; trademarks of Pni Horticulture Inc. For support, visit www.pnigreenhouse.com or contact 1-800-555-370W.

Troubleshooting

Reset: Unplug for 60 seconds to reset control board.

Service: 1-800-555-370W; www.pnigreenhouse.com