Pion Power SP100W User Manual

The Pion Power SP100W is a 100W portable power station designed for outdoor activities, emergency backup, and off-grid power needs. It features a high-capacity lithium-ion battery, multiple output ports (AC, DC, USB), pure sine wave inverter, LCD display showing battery status and output power, built-in MPPT solar charge controller, overload protection, and temperature control. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging Methods 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Pure sine wave inverter, LCD display, Solar charge input, AC output ports, DC output ports, USB ports, Cooling fan, Carrying handle.

Feature	Description
AC Output	Pure sine wave, 100W continuous power
DC Output	12V/10A car port for DC devices
USB Ports	Two USB-A (5V/2.4A) and one USB-C (PD 18W)
LCD Display	Shows battery level, input/output power, temperature
Solar Charge Input	Supports up to 100W solar panel input
AC Charge Input	Wall charger for fast AC charging
Car Charge Input	12V car charger for on-the-go charging
Overload Protection	Automatic shutdown when overloaded
Temperature Control	Built-in fan for heat dissipation
Carrying Handle	Portable design for easy transport

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect AC adapter to power station and wall outlet for full charge.
Connect solar panel: Use solar charge cable to connect compatible solar panel.
Connect devices: Plug devices into appropriate output ports (AC, DC, USB).
Power on: Press and hold power button for 3 seconds to turn on.

WARNING! Keep away from water and extreme temperatures. Do not disassemble unit.

First-Time Setup

Power on unit; check LCD display for battery status.

Fully charge battery: Use AC charger for initial 8-hour charge.
Configure settings: Use MODE button to select output type (AC/DC).
Set auto-shutdown: In settings menu, configure auto-off timer.
Test outputs: Connect small device to verify each output port works.

CAUTION! Use only compatible charging cables and devices.

Specifications

Battery Capacity: 100,000mAh/370Wh lithium-ion.
AC Output: 100W pure sine wave, 110V/60Hz.
DC Output: 12V/10A (max 120W).
USB Output: USB-A: 5V/2.4A each; USB-C: PD 18W.
Solar Input: 12-24V, up to 100W.
AC Charging: 0-100% in 8 hours.
Car Charging: 0-100% in 10 hours.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 6.6 lbs (3 kg).
Dimensions: 9.8 x 5.9 x 5.9 inches.

Controls and Settings

Front Panel: Power button, LCD display, MODE button, Output ports.

LCD Display: Shows battery percentage, input/output power, temperature warnings, error codes.

Settings Menu: Press and hold MODE for 5 seconds to access: Auto-shutdown timer (2/4/6/8 hours), Screen brightness, Buzzer on/off, Temperature unit (°C/°F). Output Control: Press MODE to cycle through AC/DC/USB outputs. Battery Protection: Low-voltage auto-shutdown at 10%.

Connecting Devices

AC Devices: Plug into AC outlets (max 100W). DC Devices: Use 12V car port. USB Devices: Connect to USB-A or USB-C ports.

Check device power requirements before connecting.
Turn off power station before connecting/disconnecting devices.
Start with low-power devices to test functionality.

Tip: Do not exceed total 100W output across all ports.

Charging Methods

Supports three charging methods: AC wall charging, Solar charging, Car charging.

AC Charging: Connect AC adapter to wall outlet and DC input port.
Solar Charging: Connect solar panel to solar input port (optimal in direct sunlight).
Car Charging: Use car charger cable while vehicle is running.
Charging Status: LCD shows charging progress and estimated time remaining.
Fast Charge: Use AC charger for fastest charging (8 hours to full).

WARNING! Use only Pion Power certified charging accessories.

Safety Features

Overload Protection: Automatic shutdown if total load exceeds 100W. Short Circuit Protection: Cuts power during short circuit. Temperature Protection: Fan activates at 95°F; shutdown at 140°F. Low Voltage Protection: Auto-shutdown at 10% battery to prevent damage.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth only; do not use liquids.

CAUTION! Do not expose to rain or moisture. Recharge every 3 months if storing long-term.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2025 Pion Power; all rights reserved. For support, visit www.pionpower.com or contact 1-800-555-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery depleted/overload	Recharge battery; reduce connected load.
Not charging	Wrong cable/poor connection	Use correct charging cable; ensure secure connection.
Overheating	High ambient temperature	Move to cooler location; allow to cool before use.
LCD not displaying	Battery completely drained	Connect to AC charger for 30 minutes.
Solar not charging	Insufficient sunlight/panel issue	Ensure direct sunlight; check solar panel connections.

Reset: Press and hold power button for 10 seconds to reset.

Service: 1-800-555-1234; www.pionpower.com