Patura 144250 Installation And Mounting Instructions

The Patura 144250 is a mounting bracket system designed for secure installation of various fixtures. This guide provides essential information for safe handling, proper installation steps, mounting procedures, and necessary precautions to ensure optimal performance and safety. Below are key sections covering safety warnings, components, installation steps, mounting guidelines, and maintenance.

1. Safety Warnings and Precautions 2. Package Contents and Components 3. Tools Required 4. Installation Steps 5. Mounting Procedure 6. Adjustment and Alignment 7. Weight and Load Specifications 8. Maintenance and Care 9. Troubleshooting 10. Warranty and Support

Safety Warnings and Precautions

Key safety instructions to prevent injury and ensure proper installation.

Warning	Description
Weight Limit	Do not exceed the maximum load capacity of 50 kg (110 lbs).
Secure Mounting	Ensure mounting surface is solid and capable of supporting the load.
Professional Installation	Recommended for heavy or complex installations.
Electrical Safety	If installing near electrical wiring, turn off power at the circuit breaker.
Periodic Inspection	Regularly check brackets and fasteners for signs of wear or loosening.

Package Contents and Components

Unpack and verify all components are present before beginning installation.

Mounting Bracket (x1): Main support structure.
Wall Plate (x1): Attaches to the wall surface.
M6 Screws (x8): For securing bracket to wall.
Wall Anchors (x8): For use in drywall or masonry.
Hex Key (x1): For tightening bolts.
Instruction Manual (x1): This document.

WARNING! Do not proceed if any components are missing or damaged. Contact support for replacements.

Tools Required

Gather the following tools before starting the installation.

Drill: For creating pilot holes.
Drill Bits: Appropriate size for wall anchors (typically 8mm).
Level: To ensure bracket is mounted evenly.
Screwdriver: Phillips head for screws.
Stud Finder: Recommended for locating wall studs.
Tape Measure: For accurate positioning.

CAUTION! Use tools properly to avoid damage to components or injury.

Installation Steps

Follow these steps in order for a secure installation.

Locate Studs: Use a stud finder to identify solid mounting points.
Mark Positions: Hold wall plate against wall, mark screw holes with a pencil.
Drill Pilot Holes: Drill holes at marked positions using appropriate drill bit.
Insert Wall Anchors: Tap anchors into holes until flush with wall.
Attach Wall Plate: Align plate with holes, secure with provided screws.
Mount Bracket: Attach main bracket to wall plate using included bolts.
Check Level: Use a level to ensure bracket is perfectly horizontal.

Tip: For masonry walls, use a hammer drill and appropriate masonry anchors.

Mounting Procedure

Attach your fixture to the installed bracket.

Prepare Fixture: Ensure fixture is compatible with bracket mounting points.
Align Fixture: Lift fixture and align its mounting holes with bracket arms.
Secure Fixture: Insert and tighten bolts through fixture into bracket.
Double-Check: Ensure all connections are tight and secure.
Test Stability: Gently apply pressure to confirm fixture is firmly mounted.

WARNING! Always have assistance when lifting heavy fixtures to avoid strain or dropping.

Adjustment and Alignment

Fine-tune the position of your mounted fixture.

Tilt Adjustment: Loosen tilt knob, adjust angle, then retighten.

Swivel Adjustment: Loosen swivel lock, rotate fixture to desired position, then lock.

Leveling: Use built-in bubble level or external level for final alignment.

Note: Do not over-tighten adjustment knobs to avoid damaging threads.

Weight and Load Specifications

Maximum Load Capacity: 50 kg (110 lbs).
Bracket Material: Powder-coated steel.
Mounting Surface: Solid wall, concrete, or studs required.
VESA Compatibility: Supports VESA patterns up to 400x400 mm.
Adjustment Range: Tilt: ±15 degrees; Swivel: ±30 degrees.

Maintenance and Care

Regular maintenance ensures longevity and safety.

Monthly Inspection: Check all bolts and screws for tightness.
Cleaning: Wipe bracket with a dry cloth; avoid abrasive cleaners.
Lubrication: Apply light machine oil to moving parts if stiffness occurs.
Environmental: Keep away from excessive moisture or corrosive substances.

CAUTION! Do not use water or liquid cleaners on bracket components.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Bracket feels loose	Insufficiently tightened screws	Tighten all screws and bolts to specified torque.
Fixture not level	Uneven mounting surface	Adjust bracket using shims or reposition wall plate.
Difficulty adjusting tilt/swivel	Overtightened adjustment knobs	Loosen knobs slightly, adjust, then retighten moderately.
Mounting holes don't align	Incorrect VESA pattern	Verify fixture's VESA pattern matches bracket compatibility.
Bracket sags under weight	Exceeds weight limit or weak wall	Reduce load or reinforce mounting surface.

Reset: If adjustments fail, dismount fixture and restart from installation step 5.

Warranty and Support

Patura 144250 includes a 5-year limited warranty covering defects in materials and workmanship. Warranty does not cover damage from improper installation, misuse, or unauthorized modifications. For technical support or warranty claims, contact Patura Customer Service at [email protected] or call 1-800-555-1442. Visit www.patura.com for additional resources and FAQs.