Ovation Solar Panel 150T User Manual

The Ovation Solar Panel 150T is a high-efficiency 150W monocrystalline solar panel designed for residential and light commercial use. It features advanced PERC cell technology, robust aluminum frame, tempered glass protection, IP67-rated junction box, and compatibility with most 12V/24V solar systems. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Monocrystalline PERC solar cells, Anodized aluminum frame, Tempered glass surface, IP67 junction box with MC4 connectors, Bypass diodes.

Installation

Unpack and inspect contents. Ensure all components are present and undamaged.

1. Choose location: Select area with maximum sunlight exposure, minimal shading.
2. Mounting: Use provided brackets to secure panel to roof or ground mount structure.
3. Orientation: Tilt panel according to latitude (typically 15-40 degrees).
4. Secure wiring: Route cables from junction box to charge controller.
5. Grounding: Connect grounding lug to proper earth ground.

WARNING! Panel is heavy and fragile; use proper lifting techniques and safety equipment. Do not install during inclement weather.

First-Time Setup

After physical installation, connect to your solar system.

1. Connect panels: Use MC4 connectors to link panels in series or parallel as needed.
2. Connect to charge controller: Route positive and negative cables to controller inputs.
3. Connect to battery: Ensure charge controller is properly connected to battery bank.
4. Verify connections: Check all connections are secure and polarity is correct.
5. Test system: Monitor charge controller display for proper voltage and current.

CAUTION! Always connect battery to charge controller BEFORE connecting solar panels. Disconnect solar panels before servicing.

Specifications

• Maximum Power (Pmax): 150W
• Open Circuit Voltage (Voc): 22.4V
• Short Circuit Current (Isc): 8.9A
• Maximum Power Voltage (Vmp): 18.6V
• Maximum Power Current (Imp): 8.1A
• Module Efficiency: >20%
• Power Tolerance: 0 ~ +5W
• Maximum System Voltage: 1000V DC
• Maximum Series Fuse Rating: 15A
• Fire Rating: Class C (UL 1703)
• Wind Load: 2400 Pa
• Snow Load: 5400 Pa

Controls and Connections

Panel has no active controls; all management occurs through connected charge controller.

Junction Box: Contains bypass diodes, positive/negative terminals with MC4 connectors.

Connections: Standard MC4 male/female connectors for easy series/parallel connection.

Grounding: Dedicated grounding lug for safety grounding connection.

Monitoring: Performance monitored through connected charge controller or monitoring system.

Connecting to System

Connect to charge controller, inverter, or battery system as required.

1. Turn off all system components before connecting.
2. Connect panels in series for higher voltage, parallel for higher current.
3. Use proper gauge wiring based on distance and current.
4. Install DC disconnect between panels and charge controller.
5. Connect to charge controller following manufacturer instructions.

Tip: Use UV-resistant solar cable for all outdoor connections. Keep cables organized and protected.

Performance Monitoring

Monitor panel performance through connected systems.

1. Check charge controller display for voltage and current readings.
2. Monitor daily energy production through compatible monitoring systems.
3. Compare actual output to expected output based on sunlight conditions.
4. Regularly check for shading or debris affecting performance.
5. Maintain performance log to track degradation over time.

Expected Performance: Under optimal conditions, 150W panel produces approximately 450-750 watt-hours daily depending on location and season.

Safety Features

Bypass Diodes: Minimize power loss from partial shading. IP67 Junction Box: Water and dust proof. Tempered Glass: Impact resistant. Frame Grounding: Proper grounding point for safety.

Care & Maintenance

Regular maintenance ensures optimal performance.

1. Cleaning: Use soft cloth or sponge with water. Clean early morning or late evening.
2. Inspection: Quarterly visual inspection for damage, loose connections, or corrosion.
3. Debris removal: Remove leaves, snow, or other obstructions.
4. Connection check: Annually verify all electrical connections are tight and corrosion-free.
5. Mounting check: Ensure all mounting hardware remains secure.

CAUTION! Never use abrasive materials or harsh chemicals. Do not walk on panel. Disconnect from system before cleaning.

Regulatory Information

Certifications: UL 1703, IEC 61215, IEC 61730. Complies with FCC Part 15 Class B for electromagnetic compatibility. CE marked for European market. RoHS compliant. Copyright © 2025 Ovation Solar Technologies. All trademarks property of their respective owners. For technical support, visit www.ovationsolar.com/support or contact 1-800-555-OVATE.

Troubleshooting

Service: For warranty claims or repairs, contact authorized service center. Do not attempt to open junction box or repair cells.

Support: 1-800-555-OVATE; www.ovationsolar.com/support