The North Light OCL-1169 is a high-performance LED task light designed for precision work. It features adjustable color temperature (2700K-6500K), dimmable brightness, a flexible gooseneck arm, a stable weighted base, USB-C power input, and a high-CRI LED for accurate color rendering. Below are key sections for safety, features, setup, operation, and maintenance.
Key components: High-CRI LED panel, Flexible Gooseneck Arm, Control Dial, Weighted Base, USB-C Power Port.
| Feature | Description |
|---|---|
| LED Panel | High CRI (>95) for accurate color rendering |
| Color Temperature | Adjustable from 2700K (Warm) to 6500K (Cool) |
| Brightness Control | Dimmable from 10% to 100% |
| Gooseneck Arm | Fully flexible for precise positioning |
| Weighted Base | Non-slip, stable design |
| Control Dial | Integrated for color temp and brightness |
| Power Input | USB-C port (5V/2A) |
| Memory Function | Remembers last used settings |
| On/Off Switch | Located on the base |
| Warranty | 3-year limited warranty |
Carefully unpack and verify all components are present.
WARNING! Inspect for shipping damage before use. Do not use if any part is damaged.
Place lamp on a stable, flat surface.
CAUTION! Do not over-bend or force the gooseneck. Support the LED head when adjusting.
Primary control is via the integrated dial on the base.
Control Dial: Rotate to adjust brightness. Press and rotate to adjust color temperature.
On/Off Switch: Mechanical switch on the base for main power.
Operation Steps: 1. Turn on using the base switch. 2. Rotate the dial clockwise to increase brightness. 3. Press the dial and rotate to cycle through color temperatures (warm to cool). 4. The lamp will remember your last brightness and color temperature setting when powered off and on.
Powered via USB-C. Compatible with most USB power sources.
Tip: For optimal performance, use a 10W (5V/2A) or higher power adapter.
Customize light for your task.
Suggested Settings: - Reading/Writing: 4000K, 70% brightness. - Detailed Craft: 5000K-6500K, 80-100% brightness. - Ambient/Relaxing: 2700K-3000K, 30-50% brightness.
Unplug the lamp before cleaning.
Cleaning: Use a soft, dry or slightly damp cloth to wipe the base and arm. Do not use abrasive cleaners or solvents on the LED panel. Use a dry microfiber cloth to gently dust the LED diffuser.
CAUTION! Never immerse the lamp in water or other liquids. Do not use compressed air to clean the LED panel.
FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © North Light. All rights reserved. North Light is a trademark of North Light Innovations, Inc. For support, visit www.northlightsupport.com or contact 1-800-555-0199.
| Symptom | Possible Cause | Corrective Action |
|---|---|---|
| Lamp does not turn on | No power | Check On/Off switch; ensure USB cable is firmly connected at both ends; try a different power source/adapter. |
| Light is dim or flickering | Insufficient power | Use the included cable with a 5V/2A (10W) or higher power adapter. |
| Control dial not responding | System lock | Turn the lamp off and on again using the base switch. |
| Gooseneck will not hold position | Wear over time | Gently tighten the adjustment collar at the base of the gooseneck (if user-serviceable, refer to website). |
| LED panel is warm | Normal operation | Some warmth is normal during extended use at high brightness. Ensure vents are not blocked. |
Reset: Unplug lamp for 60 seconds, then reconnect.
Service: 1-800-555-0199; www.northlightsupport.com