Motomaster Eliminator 11-1880-2 Instructions

The Motomaster Eliminator 11-1880-2 is a portable jump starter and power bank designed for automotive emergencies and outdoor use. It features a high-capacity lithium battery, built-in safety protections, multiple output ports (USB, 12V DC), LED flashlight with emergency modes, and jumper cables for starting vehicles. Below are key sections for safety, features, operation, charging, maintenance, and troubleshooting.

Features at a Glance

Key components: Lithium-ion battery pack, LED display, Jumper cable clamps, USB output ports, 12V DC output, LED flashlight, Power button, Charging port.

Safety Precautions

Read all instructions before use. Improper use can cause injury or damage.

1. Use only with 12V lead-acid automotive batteries. Do not use with 6V or 24V systems.
2. Ensure vehicle is off and keys are removed before connecting jumper cables.
3. Connect clamps in correct order: positive (red) to positive (+), negative (black) to negative (-) or unpainted metal ground.
4. Keep away from heat, fire, and water. Do not disassemble or puncture.
5. Store in a cool, dry place away from children.

WARNING! Risk of explosion. Do not expose to flame or extreme heat. Follow connection sequence precisely to avoid sparks.

First-Time Setup & Charging

Fully charge the unit before first use.

1. Plug the included AC adapter into the unit's charging port and a wall outlet.
2. The LED display will show charging progress. Charge until display reads 100%.
3. Once fully charged, unplug the adapter. The unit is now ready for use.
4. For long-term storage, recharge every 3-6 months to maintain battery health.

CAUTION! Use only the provided or manufacturer-approved charger. Do not leave charging unattended for extended periods.

Specifications

• Model: Eliminator 11-1880-2
• Battery Type: Rechargeable Lithium-ion
• Peak Current: [Insert Peak Amps]A
• USB Output: 5V DC, [Insert]A total
• 12V DC Output: 12V, [Insert]A max
• Flashlight: High-intensity LED with SOS and strobe
• Charging Input: 12-15V DC via included adapter
• Operating Temp: -20°C to 60°C (-4°F to 140°F)
• Storage Temp: -20°C to 45°C (-4°F to 113°F)
• Weight: Approximately [Insert] kg/lbs

Controls and Indicators

Access functions via the Power Button and LED display.

Power Button: Press once to turn on unit and check battery level on display. Press and hold for 2 seconds to turn off. Press quickly while on to cycle flashlight modes (Off -> Steady -> SOS -> Strobe).

LED Display: Shows numeric battery percentage (e.g., 80%). Flashing low battery warning below 20%.

Jumper Cable Port: Connect clamps here for jump starting. Unit must be turned ON.

USB/12V Ports: Use to power or charge external devices. Unit must be turned ON.

Jump Starting a Vehicle

Follow these steps carefully to jump start a 12V vehicle.

1. Ensure Eliminator unit is turned OFF. Park donor vehicle (if used) close but not touching.
2. Connect RED clamp to the POSITIVE (+) terminal of the dead vehicle battery.
3. Connect BLACK clamp to a clean, unpainted metal part of the engine block or chassis (ground). Do not connect to negative (-) terminal if battery is damaged, leaking, or frozen.
4. Turn ON the Eliminator unit. The display will light up.
5. Attempt to start the vehicle. Crank for no more than 3-5 seconds. Wait 30 seconds between attempts.
6. Once vehicle starts, turn OFF the Eliminator unit.
7. Disconnect clamps in REVERSE order: Black clamp first, then Red clamp.
8. Recharge the Eliminator unit as soon as possible.

WARNING! Do not touch clamps together when unit is on. Ensure clamps have firm metal-to-metal contact.

Using as a Power Bank

The unit can charge USB devices and power 12V accessories.

1. Turn ON the unit using the Power Button.
2. For USB devices: Connect your device (phone, tablet) to a USB port using your own cable. Charging will begin automatically.
3. For 12V devices: Plug the 12V accessory (e.g., air compressor, spotlight) into the 12V DC output port. The device will draw power.
4. Monitor the battery level on the display. The unit will automatically shut off if battery is too low or in case of overload.
5. Turn OFF the unit when finished to conserve battery.

Tip: The unit is not designed for continuous high-drain 12V devices. Check device power requirements first.

Flashlight & Emergency Features

The built-in LED flashlight offers multiple lighting modes.

To use: With the unit ON, press the Power Button briefly to cycle through modes: Off -> Bright Light -> SOS Signal -> Strobe Light.

Bright Light: For general illumination.

SOS Mode: Flashes international distress signal (--- *** ---). Useful for emergencies.

Strobe Mode: Rapid flashing to attract attention.

The flashlight can run for several hours depending on battery level and mode.

Care & Storage

Unplug all devices before cleaning or storage. Wipe exterior with a dry, soft cloth. Do not use liquids or solvents.

Storage: Store in the included case in a cool, dry location. Recharge to at least 50% every 3-6 months if not in use to prevent deep discharge.

CAUTION! Do not expose to direct sunlight, rain, or excessive humidity. Do not attempt to open or repair the unit.

Regulatory Information

This device complies with relevant safety and EMC standards. Contains a lithium-ion battery; follow local regulations for disposal. Do not dispose of in household trash. For recycling information, contact your local waste management authority. Motomaster is a trademark. For support, visit www.motomaster.ca or contact customer service.

Troubleshooting

Reset: Turn unit OFF, disconnect everything, wait 1 minute, then turn ON.

Service: Do not disassemble. For warranty service or support, contact Motomaster customer service or visit the website.