Logia LOWSC713SWB User Manual

The Logia LOWSC713SWB is a 7-inch Portable Solar Generator with a 155Wh capacity, featuring a pure sine wave inverter, multiple output ports (AC, DC, USB), a built-in MPPT solar charge controller, LCD display for system status, and a rugged, weather-resistant design. Ideal for camping, emergencies, and outdoor power needs. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Solar Charging 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Pure Sine Wave Inverter, MPPT Solar Charge Controller, LCD Display, AC outlets, DC car port, USB ports, Solar Input port.

Feature	Description
AC Output	2 x 110V AC outlets (300W continuous, 600W surge)
DC Output	1 x 12V DC car port
USB Ports	2 x USB-A (5V/2.4A), 1 x USB-C (PD 60W)
Solar Input	Supports up to 100W solar panel (MC4 connector)
LCD Display	Shows battery level, input/output power, warnings
Pure Sine Wave	Clean power for sensitive electronics
MPPT Controller	Maximizes solar charging efficiency
Battery Capacity	155Wh Lithium-ion
Weight	Approx. 3.5 lbs (1.6 kg)
Built-in Handle	For easy portability

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect to AC wall outlet using included adapter to fully charge unit before first use.
Solar Panel Connection: Connect compatible solar panel to SOLAR INPUT port using MC4 cables.
Device Connection: Plug devices into appropriate output ports (AC, DC, USB).
Power On: Press and hold POWER button for 3 seconds to activate unit.

WARNING! Keep unit away from water, heat sources, and flammable materials. Do not disassemble.

First-Time Setup

Power on unit; monitor LCD display.

Charge Battery: Ensure battery is fully charged via AC or solar before extended use.
Configure Settings: Use MODE button to cycle through output settings (ECO, Standard).
Monitor Display: Check battery level, input/output wattage on LCD screen.
Test Outputs: Connect a small device to each port to verify functionality.

CAUTION! Use only included or manufacturer-approved cables and solar panels.

Specifications

Battery Capacity: 155Wh (Lithium-ion).
AC Output: 110V, 60Hz, 300W continuous (600W surge).
DC Output: 12V, 10A max.
USB Output: USB-A: 5V/2.4A; USB-C: PD up to 60W.
Solar Input: 12-24V, up to 100W, MC4 connector.
AC Charging: 110-240V, 50-60Hz via included adapter.
Display: LCD with battery level, wattage, error codes.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Dimensions: 7.5 x 5 x 5 inches.

Controls and Settings

Front Panel: POWER button, MODE button, LCD display, output ports.

LCD Icons: Battery level, AC/DC/USB output status, solar input, overload warning, low battery warning.

Modes: ECO (auto power-off when device is fully charged or not in use), Standard (continuous output). Settings: Press MODE to toggle between output modes. Display: Shows real-time input/output power, estimated runtime.

Connecting Devices

AC Devices: Plug into AC outlets (max 300W total). DC Devices: Use 12V car port. USB Devices: Connect to USB-A or USB-C ports.

Check device power requirements (watts/amps) before connecting.
Ensure total connected load does not exceed 300W for AC outlets.
For solar charging, connect panel to SOLAR INPUT in adequate sunlight.

Tip: Start with the highest power device first to avoid overload.

Solar Charging

Supports 100W solar panel input via MPPT controller.

Panel Setup: Position solar panel in direct sunlight, facing the sun.
Connection: Use MC4 cables to connect panel to SOLAR INPUT port.
Monitoring: LCD will show solar input wattage and charging status.
Efficiency: MPPT controller optimizes charging even in low-light conditions.
Charging Time: Approx. 3-5 hours with 100W panel under ideal conditions.

WARNING! Do not connect solar panel while unit is powering devices. Ensure correct polarity.

Safety Features

Overload Protection: Automatically shuts off output if exceeded. Short Circuit Protection: Safeguards against DC/USB shorts. Over-temperature Protection: Reduces output if overheating. Low Battery Protection: Shuts down at 10% to prevent battery damage.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; do not use liquids. Periodically charge to 50% if storing long-term.

CAUTION! Do not expose to rain or extreme temperatures. Avoid dropping or impact.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL Certified: Meets safety standards for portable power stations. Copyright © 2025 Logia; trademarks of Logia Inc. For support, visit www.logia.com or contact 1-800-555-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't power on	Battery depleted	Charge via AC or solar for at least 30 minutes.
No output from ports	Overload/trip	Disconnect devices, wait 30 seconds, restart unit.
Solar not charging	Panel/connection	Ensure panel in sun, cables securely connected, correct port.
LCD shows error code	Fault condition	Refer to manual error code list; reset unit if needed.
Reduced runtime	Battery age/high load	Reduce connected load; consider battery replacement if old.

Reset: Hold POWER + MODE for 10 seconds to hard reset.

Service: 1-800-555-1234; www.logia.com/support