Lippert GS-STAR-200W User Manual

The Lippert GS-STAR-200W is a 200-watt portable solar power generator designed for outdoor, emergency, and off-grid applications. It features a high-capacity lithium battery, multiple output ports (AC, DC, USB), MPPT charge controller, pure sine wave inverter, LCD display for system status, and compatibility with solar panel charging. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging & Power Management 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Pure Sine Wave Inverter, MPPT Charge Controller, LCD Display, Multiple output ports, Carrying handle.

Feature	Description
AC Output	200W pure sine wave AC outlet (120V, 60Hz)
DC Output	12V/10A carport and 5.5mm DC jack
USB Ports	Dual USB-A (5V/2.4A) and USB-C PD (18W)
LCD Display	Shows battery level, input/output power, warnings
MPPT Controller	Maximizes solar panel charging efficiency
Battery	Lithium-ion, 200Wh capacity
Input Ports	Solar input (8mm DC), AC wall charger input
Power Button	Turns unit on/off
LED Light	Built-in emergency light with multiple modes
Overload Protection	Automatic shutdown on overload/short circuit

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect included AC adapter to wall outlet and unit's AC input port.
Connect Solar Panel: Use compatible solar panel with 8mm DC plug to solar input port.
Positioning: Ensure unit is in well-ventilated area, away from direct sunlight and moisture.
Grounding: For permanent installation, follow local electrical codes for grounding.

WARNING! Do not expose to rain or liquids. Keep away from children and pets.

First-Time Setup

Power on unit; monitor LCD display.

Initial Charge: Fully charge battery via AC adapter before first use (approx. 6-8 hours).
LCD Display Check: Verify battery level indicator shows 100% after charge.
Output Test: Connect small device (e.g., phone charger) to USB port to confirm operation.
Solar Setup: Connect solar panel in direct sunlight; display should show charging icon.

CAUTION! Use only approved accessories. Do not modify unit.

Specifications

Battery Capacity: 200Wh Lithium-ion.
AC Output: 200W continuous, 400W surge, 120V/60Hz pure sine wave.
DC Output: 12V/10A (carport), 12V/5A (5.5mm jack).
USB Output: USB-A: 5V/2.4A each; USB-C: 5V/3A, 9V/2A, 12V/1.5A.
Solar Input: 12-24V DC, max 100W, 8mm connector.
AC Charger Input: 100-240V AC, 50/60Hz.
LCD Display: Battery level, input/output wattage, error codes.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 5.5 lbs (2.5 kg).

Controls and Settings

Access functions via physical buttons and LCD menu. Front Panel: POWER button, LCD display, USB ports, LED light button.

LCD Menu: Press POWER button briefly to cycle display modes (battery %, input power, output power, runtime estimate).

LED Light: Press light button to cycle modes (High, Low, SOS, Strobe). Power Management: Auto-shutdown after 30 minutes with no load (configurable). Battery Saver: Enable in settings to extend battery life. Brightness: Adjust LCD backlight in settings.

Connecting Devices

AC Devices: Plug into AC outlet (max 200W). DC Devices: Use carport or 5.5mm DC jack. USB: Connect phones, tablets, etc.

Check device power requirements (watts/amps) do not exceed port limits.
Turn off device before connecting to prevent sparking.
Connect device cable to appropriate port on generator.
Turn on generator (POWER button), then turn on device.

Tip: For sensitive electronics (laptops, medical devices), use pure sine wave AC outlet.

Charging & Power Management

Supports solar, AC wall charger, and 12V car charger inputs.

Solar Charging: Connect compatible solar panel; ensure direct sunlight.
AC Charging: Use included AC adapter for fastest charge (0-100% in ~6 hours).
Car Charging: Use optional 12V car charger adapter (not included).
Monitoring: LCD shows charging current, estimated time to full.
Battery Care: For storage, charge to 50-60% and store in cool, dry place.
Parallel Use: Can connect two units for 400W output (requires optional cable).
Eco Mode: Enable to reduce standby power consumption.

WARNING! Do not charge with damaged cables. Use only approved solar panels.

Safety Features

Overload Protection: Auto-shutdown if load exceeds 200W. Short Circuit Protection: Cuts output on short circuit. Temperature Control: Reduces output if overheated. Low Voltage Protection: Shuts off when battery drops below 10% to prevent damage.

Care & Maintenance

Unplug all devices before cleaning. Use dry, soft cloth only; do not use liquids.

CAUTION! Do not disassemble unit. Avoid extreme temperatures. Recharge every 3 months if storing long-term.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL 2743 certified for portable power stations. Copyright © 2023 Lippert Components, Inc. For support, visit www.lci1.com or contact 1-574-537-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Charge via AC adapter for 30 minutes, then try again.
No output power	Overload/overheat	Reduce connected load; allow unit to cool; restart.
Solar not charging	Panel/connection	Ensure panel in direct sun; check cable connection; verify panel voltage.
LCD display blank	Sleep mode/battery	Press any button to wake; if still blank, charge battery.
AC outlet not working	Overload protection	Disconnect all devices; press reset button (if equipped); reconnect one device at a time.

Reset: Hold POWER button for 10 seconds to force restart.

Service: 1-574-537-1234; www.lci1.com