Ledino LED-FLA1005IR-Set Quick Start Manual

The Ledino LED-FLA1005IR-Set is a versatile LED floodlight kit featuring infrared motion sensor technology, designed for outdoor security and area illumination. It includes weather-resistant construction, adjustable sensor range and sensitivity, multiple lighting modes (constant on, auto, off), dusk-to-dawn operation, and easy mounting. Powered by standard household voltage. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Using the Motion Sensor 8. Maintenance 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-power LED floodlight, Passive Infrared (PIR) motion sensor, adjustable mounting bracket, weatherproof housing, and power cable.

Feature	Description
LED Light Source	High-efficiency LEDs for bright, energy-saving illumination
PIR Motion Sensor	Detects movement up to a configurable range (e.g., 10m/33ft)
Detection Angle	Wide-angle coverage (e.g., 120° horizontal)
Lighting Modes	Switch between AUTO (sensor-activated), ON (constant), OFF
Dusk-to-Dawn Sensor	Activates light only in low ambient light conditions
Adjustable Settings	Time delay, sensitivity, and lux (ambient light) adjustment
Weatherproof Rating	IP65 rated for dust and water resistance
Mounting Bracket	Adjustable for aiming light in desired direction
Power Input	Connects to standard AC mains (e.g., 100-240V~, 50/60Hz)
Installation	Wall or ceiling mount with included hardware

Installation

Unpack and inspect contents. Ensure power is OFF at the circuit breaker before beginning.

Choose Location: Select a suitable outdoor location (wall, eave, post) that provides clear coverage of the area to be monitored and illuminated.
Mount Bracket: Use the provided template (if included) to mark drill holes. Secure the mounting bracket using appropriate screws and anchors for your surface.
Wire Connection: Pass the power cable through the cable gland on the light housing. Connect the wires (Live, Neutral, Earth/Ground) to your household wiring according to local electrical codes. Ensure all connections are secure and insulated.
Attach Light: Mount the floodlight onto the bracket and tighten the adjustment knobs securely.
Seal Entry Point: Tighten the cable gland to ensure a weatherproof seal around the power cable.

WARNING! Installation should be performed by a qualified electrician. Ensure the circuit is de-energized before working on wiring. Do not install near heat sources or flammable materials.

First-Time Setup

After installation, restore power and configure the sensor settings.

Power On: Turn on the circuit breaker. The light may flash once to indicate power.
Set Mode: Use the mode switch (often on the sensor housing or inside a cover) to select AUTO.
Adjust Sensitivity (SENS): Turn the sensitivity dial to mid-range. Test by walking within the detection zone. Increase for greater range/sensitivity, decrease to avoid false triggers.
Adjust Time Delay (TIME): Set how long the light stays on after motion ceases (e.g., from 5 seconds to 10 minutes). Start with a medium setting (e.g., 1 minute).
Adjust Lux Level (LUX): Set the ambient light threshold. Turn fully clockwise (max) for light to operate only at night. Turn counter-clockwise for the light to activate even in daylight if motion is detected.
Aim Sensor: Loosen the adjustment knobs and point the sensor lens towards the primary detection area. Avoid pointing directly at heat sources, moving foliage, or busy streets to reduce false alarms.

CAUTION! Do not open the housing while powered on. Make adjustments with dry hands.

Specifications

Model: LED-FLA1005IR-Set
Light Source: High-Power LED Array
Luminous Flux: [e.g., 1000 Lumens]
Color Temperature: [e.g., 4000K Cool White]
Sensor Type: Passive Infrared (PIR)
Detection Range: Up to [e.g., 10 meters / 33 feet] (adjustable)
Detection Angle: [e.g., 120°]
Light Duration: Adjustable, [e.g., 5 sec – 10 min]
Operating Voltage: [e.g., 100-240V AC, 50/60Hz]
Power Consumption: [e.g., 10W]
Ingress Protection: IP65
Operating Temperature: [e.g., -20°C to +40°C]
Housing Material: Die-cast Aluminum/Plastic

Controls and Settings

Settings are adjusted via dials or switches located under a weatherproof cover on the sensor housing.

Mode Switch (OFF/AUTO/ON):
OFF: Light and sensor are disabled.
AUTO: Light activates based on motion and ambient light (LUX) settings.
ON: Light remains on constantly, ignoring sensor.

Adjustment Dials:
SENS (Sensitivity): Controls the detection range and sensitivity to movement.
TIME (Delay): Sets the duration the light stays on after the last detected motion.
LUX (Ambient Light): Sets the darkness level required for the light to activate.

Physical Adjustment: Loosen the knobs on the mounting bracket to tilt the light and sensor up/down and left/right.

Connecting to Power

The light must be connected to a permanent live AC supply with a protective earth (ground).

Ensure the main power is OFF.
Connect the light's Brown (or Black) wire to the LINE/LIVE terminal.
Connect the light's Blue (or White) wire to the NEUTRAL terminal.
Connect the light's Green/Yellow wire to the EARTH/GROUND terminal.
Secure all connections in a suitable outdoor-rated junction box.

Tip: Use conduit for exposed wiring runs to provide additional physical and weather protection.

Using the Motion Sensor

For optimal performance in AUTO mode:

Walk Test: After configuration, walk through the detection zone. The light should turn on within 1-2 seconds.
Fine-Tune: If the light does not turn on, increase SENSITIVITY. If it turns on for non-target movement (like trees), decrease SENSITIVITY or re-aim the sensor.
Time Delay: Adjust the TIME setting based on need. A shorter time saves energy; a longer time provides extended illumination.
Night-Only Operation: For security lighting, set the LUX dial to maximum so the light only operates in complete darkness.
Constant Light: Switch to ON mode for parties or when continuous area light is needed.

WARNING! Do not stare directly into the LED light. The sensor is designed to detect moving heat sources; very slow movement or objects blocked by glass may not be detected.

Maintenance

Periodic maintenance ensures long-term performance.

Cleaning: Turn OFF power. Wipe the lens and housing with a soft, damp cloth. Do not use abrasive cleaners or solvents.
Inspection: Check for loose mounting hardware, cracks in the housing, or water ingress. Ensure the cable gland is tight.
Sensor Lens: Keep the Fresnel lens (the plastic cover over the sensor) clean from dirt, spider webs, or snow for reliable detection.

CAUTION! Always disconnect power before cleaning or servicing. Do not open the sealed electronics compartment.

Regulatory Information

This product complies with relevant safety and electromagnetic compatibility (EMC) directives. It is designed for outdoor use in dry or damp locations. Disposal must be in accordance with local regulations for electronic waste (WEEE). The LED light source is not user-replaceable; the entire unit must be replaced at end of life. For support, visit the manufacturer's website or contact customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Light does not turn on	No power, Mode switch set to OFF, LUX set too high	Check circuit breaker and wiring. Set mode to AUTO or ON. Adjust LUX dial to minimum to test.
Light stays on constantly	Mode switch in ON, TIME dial set to maximum, High sensitivity causing continuous triggering	Set mode to AUTO. Reduce TIME setting. Decrease SENSITIVITY and ensure sensor is not aimed at a heat source or moving object.
Light does not detect motion	Sensor obstructed, SENS dial set too low, Object moving outside range/angle	Clean sensor lens. Increase SENSITIVITY. Re-aim sensor to cover desired area.
Light turns on during the day	LUX dial set too low	Adjust LUX dial clockwise to increase the required darkness level.
Short cycling (on/off rapidly)	Over-sensitive sensor detecting small movements (bugs, leaves)	Decrease SENSITIVITY. Re-position light away from trees or shrubs.
Water inside housing	Damaged seal or loose cable gland	Turn OFF power immediately. Disconnect and inspect. Tighten cable gland or replace unit if seals are compromised.

Reset: Turn power OFF for 30 seconds, then back ON. Readjust all settings (MODE, SENS, TIME, LUX).

Service: For persistent issues, contact customer support or a qualified electrician. Do not attempt to repair the unit yourself.