Jbe Cctv SPS-80W Quick Start Manual

The Jbe Cctv SPS-80W is an 80-watt Solar Power System designed for CCTV camera setups, featuring a high-efficiency monocrystalline solar panel, deep-cycle battery, intelligent charge controller with MPPT technology, weatherproof enclosure, multiple output ports (12V DC, 5V USB), and support for continuous camera operation. Ideal for remote surveillance locations. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Indicators 6. Connecting Devices 7. Operation Modes 8. Maintenance & Safety 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Solar Panel, Charge Controller, Battery Unit, Weatherproof Enclosure, Mounting Hardware, DC Output Ports.

Feature	Description
Solar Panel	80W monocrystalline panel with high conversion efficiency
Charge Controller	MPPT technology for optimal charging; LCD display
Battery Unit	Deep-cycle 12V/20Ah sealed lead-acid battery
Weatherproof Enclosure	IP65 rated for outdoor protection
DC Output Ports	12V DC output for CCTV cameras; 5V USB for accessories
Mounting Hardware	Adjustable brackets for panel and enclosure
LCD Display	Shows battery status, solar input, load output
Overload Protection	Automatic cut-off to prevent damage
Low Voltage Disconnect	Protects battery from deep discharge
Remote Monitoring Port	Optional connectivity for system monitoring

Installation

Unpack and inspect all components. Choose a location with maximum sunlight exposure.

Mount Solar Panel: Use brackets to secure panel facing south (northern hemisphere) at optimal angle.
Position Enclosure: Mount weatherproof enclosure in a shaded, ventilated area near camera.
Connect Solar Panel to Controller: Use provided cables; connect positive (+) and negative (-) terminals.
Connect Battery to Controller: Attach battery terminals to controller's BAT input.
Connect CCTV Camera: Plug camera into 12V DC output port.
Ground the System: Attach grounding wire to earth ground point for safety.

WARNING! Install during daylight; avoid shading on panel. Ensure all connections are tight and waterproof.

First-Time Setup

After installation, power on the system and configure settings.

Initial Charge: Allow solar panel to charge battery fully (LCD shows 100%).
Configure Controller: Press SET button on controller to set battery type (select SLA).
Set Load Output: Configure output voltage (12V default) and timer if needed.
Test Camera: Power on CCTV camera; verify feed and night vision operation.
Check Indicators: Ensure all LED/LCD indicators show normal status (green).

CAUTION! Do not connect loads exceeding 80W total. Keep battery terminals covered.

Specifications

Solar Panel: 80W Monocrystalline, 12V/6.67A.
Battery: 12V/20Ah Sealed Lead-Acid (SLA), maintenance-free.
Controller: MPPT, 10A max charge current, LCD display.
Output Ports: 12V DC (max 6A), 5V USB (2.1A).
Enclosure: IP65, ABS material, dimensions 300x200x150mm.
Operating Temp: -20°C to 60°C.
Warranty: 2 years on panel, 1 year on battery/controller.

Controls and Indicators

Charge Controller Front Panel: LCD Display, SET Button, UP/DOWN Buttons, LED Indicators (Solar, Battery, Load).

LCD Display: Shows battery voltage (V), charging current (A), load current (A), battery level (%).

Settings Menu: Access by pressing SET for 3 seconds. Navigate with UP/DOWN to adjust: Battery Type (SLA, Gel, Flooded), Load Timing (On/Off schedules), Voltage Protections (LVD/HVD).

LED Indicators: Solar (green=charging, off=no sun), Battery (green=good, red=low), Load (green=on, red=overload).

Connecting Devices

Connect CCTV cameras and accessories to output ports.

Ensure system is powered off before connecting devices.
Plug CCTV camera into 12V DC port using provided cable.
Connect accessories (e.g., IR illuminator) to USB port if 5V required.
Power on system; verify device operation on controller display.

Tip: Use only 12V DC cameras with current draw under 6A total. Do not short-circuit outputs.

Operation Modes

System operates automatically based on sunlight and load.

Day Mode: Solar panel charges battery; powers load directly if sufficient sun.
Night Mode: Battery powers load; low voltage disconnect protects battery.
Timer Mode: Set load on/off times via controller (e.g., camera recording schedule).
Manual Override: Press LOAD button on controller to force load on/off.
Monitoring: Check LCD regularly for system status; note any warning indicators.

WARNING! Do not disconnect battery while solar panel is charging. Avoid covering panel during operation.

Maintenance & Safety

Regular maintenance ensures longevity and safety.

Clean solar panel monthly with soft cloth and water; remove dust/snow.
Check battery terminals quarterly for corrosion; tighten connections.
Inspect enclosure seals annually; ensure no water ingress.
Store system in dry place if not in use for extended periods.

CAUTION! Disconnect solar panel before servicing. Do not open battery compartment. Keep away from flammable materials.

Regulatory Information

Complies with FCC Part 15 Class B, CE, RoHS. Copyright © 2025 Jbe Cctv; all trademarks property of Jbe Security Systems Ltd. For technical support, visit www.jbecctv.com/support or contact +1-800-555-0199.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery low/disconnected	Check battery connections; charge via solar or external charger.
Solar not charging	Shading/faulty panel	Ensure full sun exposure; check panel cables for damage.
Load turns off randomly	Low voltage disconnect	Reduce load or increase battery capacity; check battery health.
LCD display blank	Controller power issue	Verify battery voltage >10V; reset controller by disconnecting solar/battery.
Overload warning	Excessive load connected	Disconnect some devices; ensure total load < 80W.

Reset: Disconnect solar and battery for 30 seconds, then reconnect.

Service: +1-800-555-0199; www.jbecctv.com/support