Jasco PRO Series Quick Start Manual

The Jasco PRO Series represents a line of professional-grade smart home devices designed for reliability and advanced automation. This manual covers essential setup, configuration, and operation procedures for devices such as smart switches, dimmers, outlets, and hubs. Below are key sections for installation, pairing, programming, and troubleshooting.

1. Package Contents 2. Safety Information 3. Installation & Wiring 4. Device Pairing 5. Programming & Automation 6. Specifications 7. Advanced Features 8. Factory Reset 9. Regulatory & Compliance 10. Troubleshooting

Package Contents

Ensure all components are present before installation.

Item	Description
Jasco PRO Device	Smart switch, dimmer, outlet, or hub
Mounting Screws	For securing device to electrical box
Wire Nuts	For secure wire connections
Quick Start Guide	This manual
Decorative Wall Plate	Optional, depending on model
Antenna (for hub models)	For extended wireless range

Safety Information

Read all safety instructions before installation.

Turn off power at the circuit breaker before installation.
Use only with standard 120V AC, 60Hz wiring.
Ensure wires are properly insulated and secured.
Do not install in wet locations unless rated for damp environments.

WARNING! Risk of electric shock. Installation should be performed by a qualified electrician if you are unsure.

Installation & Wiring

Follow these steps for safe and correct installation.

Turn off power at the circuit breaker and verify it is off.
Remove existing wall plate and device from electrical box.
Connect wires: Line (black), Load (red), Neutral (white), Ground (green/bare).
Secure device in electrical box using provided screws.
Attach wall plate and restore power.

CAUTION! Ensure all connections are tight and wires are not pinched.

Device Pairing

Pair your Jasco PRO device with a compatible hub or controller.

Put your hub/controller into inclusion/pairing mode.
On the Jasco device, press and hold the button until the LED flashes.
Wait for confirmation from the hub (beep or LED indicator).
Test control from the hub app to verify pairing.

Tip: For Z-Wave devices, ensure the hub is within range (approx. 100 feet indoors).

Programming & Automation

Schedules: Set on/off times via hub app.
Scenes: Group multiple devices for simultaneous control.
Notifications: Receive alerts for device status changes.
Energy Monitoring: Track power usage (supported models).
Voice Control: Compatible with Amazon Alexa, Google Assistant.

Specifications

Voltage: 120V AC, 60Hz.
Wireless Protocol: Z-Wave Plus, Zigbee, or Wi-Fi (model dependent).
Range: Up to 100 feet indoors (Z-Wave).
Load Rating: Up to 15A resistive, 1800W.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Warranty: Limited 2-year warranty.

Advanced Features

Access advanced settings via your hub's app or through device-specific commands.

Configuration Parameters: Adjust dimming speed, default brightness, LED indicator behavior.

Association Groups: Direct device-to-device control without hub intervention.

Firmware Updates: Perform via hub if available to ensure latest features and security.

Factory Reset

Use this procedure to remove the device from your network or troubleshoot issues.

Turn device on and off three times quickly.
On the fourth cycle, leave it on until the LED flashes rapidly.
Wait for the device to reset (LED turns solid, then off).
Re-pair the device if needed.

Note: Factory reset will erase all programming and associations.

Regulatory & Compliance

FCC Part 15: This device complies with Class B digital device limits. ICES-003: Complies with Canadian EMI standards. This product contains Z-Wave technology licensed from Sigma Designs. For full compliance details, visit www.jascoproducts.com.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Device not responding	Power loss, poor connection	Check circuit breaker; verify wiring; ensure device is powered.
Cannot pair with hub	Out of range, hub not in pairing mode	Move device closer to hub; ensure hub is in inclusion mode; factory reset device.
LED indicator not lighting	Configuration setting, faulty device	Check LED settings in app; verify installation; contact support if issue persists.
Device turns on/off randomly	Interference, faulty switch	Check for nearby wireless interference; ensure proper load rating; test with different load.
Dimming not smooth	Incompatible bulb type	Use dimmable LED or incandescent bulbs; check bulb compatibility list.

Support: 1-800-654-8483; www.jascoproducts.com/support