Harbor Freight Tools 62443 Owner's Manual - Safety Instructions

This manual contains important safety instructions for the Harbor Freight Tools 62443. Read and understand all warnings, cautions, and instructions before operating, servicing, or maintaining this tool. Failure to follow these instructions can result in serious personal injury, property damage, or death. Keep this manual for future reference.

General Safety Rules

Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

Work Area Safety

Keep your work area clean and well lit. Cluttered or dark areas invite accidents.

1. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
2. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control.
3. Secure the workpiece. Use clamps or a vise to hold the workpiece. It is safer than using your hand and frees both hands to operate the tool.

WARNING! Do not use the tool where there is a risk of causing fire or explosion.

Electrical Safety

Power tool plugs must match the outlet. Never modify the plug in any way.

1. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators.
2. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
3. Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts.
4. When operating a power tool outdoors, use an extension cord suitable for outdoor use.

CAUTION! Risk of electric shock. Inspect cords and plugs before each use.

Personal Safety

• Protective Equipment: Always wear ANSI-approved safety goggles, dust mask, and hearing protection.
• Dress Properly: Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts.
• Secure Work: Use clamps or a vise to hold work when practical. It is safer than using your hand.
• Stance: Maintain proper footing and balance at all times.
• No Drugs/Alcohol: Do not operate any tool when you are tired, ill, or under the influence of drugs, alcohol, or medication.

Tool Use and Care

Use the correct tool for your application. The correct tool will do the job better and safer.

Operation: Do not force the tool. Use the correct tool for your application. Use clamps or other practical ways to secure and support the workpiece.

Maintenance: Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool.

Service

Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

1. Do not attempt to repair or modify the tool yourself unless you are qualified.
2. Use only accessories and attachments that are recommended by the manufacturer.
3. Periodically inspect the tool for damage, misalignment, binding of moving parts, or other conditions that may affect safe operation.

Tip: Always refer to this manual for maintenance instructions.

Specific Safety Warnings for Tool 62443

This tool is designed for specific applications. Misuse can cause injury.

1. Always wear safety goggles and hearing protection.
2. Ensure all guards are in place and working properly before operating.
3. Do not use the tool if the switch does not turn it on and off.
4. Keep hands away from cutting area and moving parts.
5. Allow the tool to come to a complete stop before setting it down.
6. Do not leave the tool running unattended.
7. Use only the recommended voltage as marked on the tool's nameplate.
8. Check for damaged parts before use. A guard or other part that is damaged should be properly repaired or replaced.

WARNING! Do not operate this tool without reading and understanding the entire manual.

Safety Symbols

The following table depicts the safety symbols used on the tool or in this manual.

Intended Use

The Harbor Freight Tools 62443 is intended for [Describe intended use, e.g., cutting, grinding, sanding specific materials]. Any use other than its intended purpose is considered misuse and can create hazards.

CAUTION! Do not use this tool for any application other than that for which it was designed.

Hazard Classification

This tool may present the following hazards if misused: Cutting Hazard, Entanglement Hazard, Electric Shock Hazard, Fire Hazard, Noise Hazard, Vibration Hazard, and Dust/Respiratory Hazard.

Reset: If the tool malfunctions, disconnect from power source immediately.

Service: For service, repair, or parts, contact Harbor Freight Tools Customer Service at 1-800-444-3353 or visit www.harborfreight.com.

Contact Information

Harbor Freight Tools USA, Inc. 3491 Mission Oaks Blvd. Camarillo, CA 93011. For technical questions, replacement parts, or to locate a service center, please call 1-800-444-3353 or visit our website at www.harborfreight.com.

Warranty: This product is covered by a [e.g., 90-Day] warranty. Proof of purchase is required.