Gölz BL-400M User Manual

The Gölz BL-400M is a professional-grade industrial blender with a 400W motor, stainless steel construction, variable speed control, pulse function, thermal overload protection, and a 1.5-liter BPA-free jug. Designed for commercial kitchens, bars, and food service establishments. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Operating Instructions 7. Cleaning & Maintenance 8. Safety Features 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: 400W high-torque motor, Stainless Steel Blade Assembly, Variable Speed Dial, Pulse Button, Thermal Cut-Off, Non-Slip Feet, 1.5L Tritan Jug with Lid.

Feature	Description
Motor Power	400W industrial-grade motor with high starting torque
Construction	Stainless steel housing and blade assembly
Speed Control	Variable speed dial (1-10) for precise texture control
Pulse Function	Momentary high-speed burst for tough ingredients
Jug Capacity	1.5 liters, made from BPA-free Tritan material
Safety Lock	Interlock system prevents operation unless jug is correctly seated
Thermal Protection	Automatic cut-off to prevent motor overheating
Non-Slip Feet	Rubberized feet for stability during operation
Power Cord	1.8m heavy-duty cord with storage wrap
Warranty	2-year commercial use warranty

Installation

Unpack and inspect all components. Place on clean, dry, stable surface.

Assemble jug: Place blade assembly into jug base and twist clockwise to lock.
Position unit: Ensure blender is on a flat, stable counter away from edges.
Check power: Verify voltage matches local supply (220-240V AC, 50/60Hz).
Plug in: Connect to grounded power outlet.

WARNING! Do not operate near water. Ensure hands are dry when handling plug. Keep cord away from hot surfaces.

First-Time Setup

Before first use, clean all parts thoroughly.

Wash jug, lid, and blade assembly in warm soapy water. Rinse and dry.
Wipe motor base with damp cloth. Do not immerse in water.
Perform test run: Add 1L water, secure lid, select speed 5 for 30 seconds.
Check for leaks or unusual noises. If present, turn off and inspect assembly.

CAUTION! Never operate without liquid in jug. Always secure lid before starting.

Specifications

Model: Gölz BL-400M
Motor Power: 400W (Peak 550W)
Voltage: 220-240V AC, 50/60Hz
Jug Material: BPA-free Tritan
Capacity: 1.5 Liters (max fill line 1.2L)
Blade Material: Stainless Steel (4-point star design)
Speed Settings: Variable 1-10 + Pulse
Dimensions (HxWxD): 42cm x 18cm x 18cm
Weight: 3.8 kg
Noise Level: <85 dB at maximum speed

Controls and Settings

Control Panel: POWER Button (On/Off), Variable Speed Dial (1-10), PULSE Button.

Speed Guide: 1-3 (Mixing/Stirring), 4-6 (Sauces/Soups), 7-8 (Smoothies), 9-10 (Crushing Ice), PULSE (Chopping/Emulsifying).

Operation: Ensure jug is properly seated (audible click). Turn dial to desired speed. For pulse, press and hold PULSE button. Always start at low speed, gradually increase. Maximum continuous run time: 2 minutes at high speed, then allow 5-minute cool-down.

Operating Instructions

For optimal performance and safety.

Prepare ingredients: Cut into 2-3cm pieces for even blending.
Load jug: Add liquids first, then solids. Do not exceed max fill line (1.2L).
Secure lid: Ensure lid is locked with vent cap in place.
Select speed: Start low, increase gradually to desired setting.
Use pulse: For chunky textures, use short pulses (1-2 seconds each).
Stop: Turn dial to 0, then press POWER button to off.
Wait: Allow blades to stop completely before removing lid.

Tip: For hot liquids, fill only halfway and start at lowest speed with lid vent open.

Cleaning & Maintenance

Unplug unit before cleaning. Never immerse motor base in water.

After use: Rinse jug immediately with warm water.
Deep clean: Add warm water and drop of dish soap. Run on speed 5 for 30 seconds. Rinse thoroughly.
Blade assembly: Remove carefully (sharp!). Clean with brush. Dry completely before reassembly.
Exterior: Wipe with damp cloth. Do not use abrasive cleaners.
Storage: Store with cord wrapped, jug separate to prevent odor.

CAUTION! Blades are extremely sharp. Handle with care during cleaning.

Safety Features

Interlock System: Motor will not operate unless jug is correctly seated and locked. Thermal Overload Protection: Automatic shut-off if motor overheats; reset after 30-minute cool-down. Non-Slip Feet: Prevents walking during operation. Ventilated Base: Allows airflow to prevent overheating.

Regulatory Information

CE Certified: Complies with European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU. RoHS Compliant: Contains no restricted hazardous substances. Waste Electrical: Dispose of according to local WEEE regulations. Manufacturer: Gölz GmbH, Industriestraße 12, 73630 Remshalden, Germany. For support, visit www.goelz-appliances.com or contact +49 (0)7151 9771-0.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Motor doesn't start	Jug not locked / Thermal cut-off active	Ensure jug is properly seated; Wait 30 minutes if overheated.
Poor blending results	Overfilled / Incorrect speed	Do not exceed max fill line; Use higher speed for harder ingredients.
Unusual noise/vibration	Foreign object / Loose blade	Stop immediately, unplug, check for foreign objects; Tighten blade assembly.
Leaking from jug base	Worn seal / Cracked jug	Replace sealing ring (Part #BL-400M-SEAL); Contact support if jug cracked.
Motor stops during use	Overheating / Overload	Allow to cool for 30 minutes; Reduce load or continuous run time.

Reset Thermal Cut-Off: Unplug, wait 30 minutes, plug back in.

Service: +49 (0)7151 9771-0; www.goelz-appliances.com/support