Generark SolarPower 2 User Manual

The Generark SolarPower 2 is a high-capacity portable power station designed for emergency backup and off-grid power needs. It features a 2000Wh lithium-ion battery, multiple AC outlets, USB ports, DC outputs, and integrated MPPT solar charging. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: High-capacity lithium battery, LCD display, AC/DC outputs, solar input, and control panel.

Installation

Unpack and inspect contents. Place on stable, dry surface.

1. Initial Charge: Connect to AC wall outlet using included adapter for full charge.
2. Solar Panel Setup: Connect compatible solar panels to solar input port.
3. Device Connection: Plug devices into appropriate AC, USB, or DC ports.
4. Power On: Press and hold power button for 3 seconds to activate.

WARNING! Keep away from water and extreme temperatures. Do not disassemble.

First-Time Setup

Power on unit; monitor LCD display.

1. Initial Charge: Charge fully via AC before first use.
2. LCD Check: Verify display shows battery percentage and status.
3. Output Test: Connect a small device to test AC and USB ports.
4. Solar Setup: Connect solar panels in direct sunlight for charging test.

CAUTION! Use only Generark-approved solar panels and accessories.

Specifications

• Battery Capacity: 2000Wh (Lithium-ion).
• AC Output: 120V, 60Hz, 2000W (4000W surge).
• USB Output: USB-C PD 100W, USB-A QC 3.0 18W.
• DC Output: 12V/10A car port, DC5521 12V/3A.
• Solar Input: 11-60V DC, 500W max, MPPT.
• AC Charging: 0-100% in approx. 7 hours.
• Cycle Life: 2000+ cycles to 80% capacity.
• Operating Temp: 14°F to 104°F (-10°C to 40°C).
• Dimensions: 15.7 x 10.6 x 10.2 inches.

Controls and Settings

Access functions via control panel buttons and LCD display.

Control Panel: Power Button, AC Button, DC Button, USB Button, LED Light Button.

LCD Display: Shows battery percentage, input/output power, estimated runtime. Settings: ECO Mode (auto power-off when no load), LCD brightness adjustment, alarm settings for low battery/overload. Charging: Select AC or solar priority in settings menu.

Connecting Devices

AC Devices: Plug into AC outlets (max 2000W total). USB Devices: Use USB-C/USB-A for phones, tablets, laptops. DC Devices: Connect to 12V car port or DC5521 ports.

1. Check device power requirements (watts/amps).
2. Ensure total load does not exceed 2000W.
3. Turn on AC/USB/DC output via corresponding button.
4. Monitor LCD for power draw and battery level.

Tip: Start with highest priority devices during emergencies.

Solar Charging

Supports solar charging with MPPT for efficiency.

1. Connect solar panels to solar input port (XT60 connector).
2. Ensure panels are in direct sunlight, angled properly.
3. LCD will show solar input power and charging status.
4. Full charge time varies by panel wattage and sunlight.
5. Use parallel connection for multiple panels (max 500W).

WARNING! Do not exceed max solar input voltage (60V DC). Use only recommended panels.

Safety Features

Overload Protection: Auto-shutoff if load exceeds 2000W. Short Circuit Protection: Cuts output during short circuit. Temperature Control: Reduces charging current if overheated. Low Battery Alarm: Alerts at 10% battery. Battery Management System (BMS): Monitors cell voltage/temperature.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth; avoid liquids. Recharge every 3 months if storing long-term. Check connections periodically for corrosion.

CAUTION! Do not expose to rain or fire. Do not attempt to repair internal components.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL Certified: Meets safety standards. Copyright © 2025 Generark; trademarks of Generark Inc. For support, visit www.generark.com or contact 1-800-555-1234.

Troubleshooting

Reset: Hold power button for 10 seconds to hard reset.

Service: 1-800-555-1234; www.generark.com