Gasolarxy PG-GSP100W Installation Manual

The Gasolarxy PG-GSP100W is a 100W portable solar power generator designed for outdoor activities, emergency backup, and off-grid power needs. It features a high-efficiency monocrystalline solar panel, integrated lithium battery, multiple output ports (AC, DC, USB), intelligent charge controller, LCD display for system status, overload protection, and weather-resistant construction. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operation & Charging 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Solar Panel, Power Generator Unit, Charge Controller, LCD Display, Output Ports, Carrying Handle.

Feature	Description
Solar Panel	100W monocrystalline with high conversion efficiency
Battery Capacity	Integrated 296Wh lithium-ion battery
AC Output	Pure sine wave 110V/60Hz, 300W (600W surge)
DC Output	12V/10A car port for DC devices
USB Ports	2x USB-A (5V/2.4A), 1x USB-C (PD 60W)
LCD Display	Shows battery level, input/output power, warnings
Charge Controller	MPPT technology for optimal solar charging
Input Ports	Solar input (DC), AC wall charger input
Overload Protection	Automatic shutdown on overload/short circuit
Carrying Handle	Integrated for portability

Installation

Unpack and inspect contents. Choose optimal location for solar panel.

Position Solar Panel: Place in direct sunlight, facing south (northern hemisphere) at optimal angle.
Connect Solar Panel to Generator: Use provided cable to connect panel's output to generator's SOLAR INPUT port.
Grounding (if required): Connect grounding wire to grounding terminal for safety.
Initial Charge: Allow solar panel to charge battery for 4-6 hours before first use.

WARNING! Do not install in shaded areas or near heat sources. Ensure all connections are dry and secure.

First-Time Setup

Power on generator; follow LCD display prompts.

Initial Charge: Connect to solar panel or AC wall charger until battery reaches 100%.
LCD Configuration: Press POWER button to turn on, navigate settings with MODE button.
Output Selection: Choose output type (AC/DC/USB) based on connected device.
Load Connection: Connect devices starting with lowest power draw first.

CAUTION! Keep generator on stable, flat surface. Avoid exposure to rain during operation.

Specifications

Solar Panel: 100W Monocrystalline, 22% efficiency.
Battery: 296Wh Lithium-ion, 800+ cycle life.
AC Output: 110V~60Hz, 300W continuous, 600W surge.
DC Output: 12V/10A (car port), 12V/5A (DC5521).
USB Output: USB-A: 5V/2.4A each; USB-C: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/3A.
Solar Input: 12-28V DC, 10A max.
AC Charging Input: 110V/60Hz, 65W max.
Operating Temp: -4°F to 140°F (-20°C to 60°C).
Weight: 13.2 lbs (6 kg) including solar panel.

Controls and Settings

Access settings via buttons on control panel. Front Panel: POWER, MODE, LCD display, output ports.

LCD Display Icons: Battery level, Solar input, AC output, DC output, USB output, Warning indicators.

Settings: Battery save mode (enable/disable), LCD brightness, output voltage adjustment (DC), auto-shutdown timer. Protection: Overload, short circuit, over-temperature, low voltage cutoff.

Connecting Devices

AC Devices: Use AC output port (max 300W). DC Devices: Use 12V car port or DC5521 port. USB Devices: Use USB-A or USB-C ports.

Check device power requirements (Watts/Amps).
Ensure total connected load does not exceed 300W.
Connect device cable to appropriate port.
Press corresponding output button to activate power.

Tip: Start with low-power devices first to prevent initial surge overload.

Operation & Charging

Supports solar charging, AC wall charging, and car charging (with optional adapter).

Solar Charging: Connect solar panel, position in sun. LCD shows charging status.
AC Charging: Plug AC adapter into wall outlet and generator's AC INPUT.
Operation: Press POWER to turn on, select outputs as needed.
Monitoring: Watch LCD for battery level and output power.
Auto-shutdown: Enable in settings to conserve battery when not in use.
Battery Save Mode: Extends battery life by limiting maximum discharge.

WARNING! Do not connect devices exceeding rated capacity. Disconnect during thunderstorms.

Safety Features

Overload Protection: Automatically cuts power if load exceeds 300W. Short Circuit Protection: Detects and disables output. Temperature Control: Reduces output if overheated. Low Voltage Cutoff: Prevents battery damage by shutting down at 10% capacity.

Care & Maintenance

Keep unit clean and dry. Store in cool, dry place when not in use.

Cleaning: Use dry cloth for solar panel and casing. Do not use chemicals.
Battery: Charge to 50-60% if storing for more than 3 months.
Inspection: Regularly check cables and ports for damage.

CAUTION! Do not disassemble unit. No user-serviceable parts inside.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE, RoHS compliant. Copyright © 2025 Gasolarxy; all rights reserved. For support, visit www.gasolarxy.com or contact 1-800-555-ENERGY.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery depleted/off	Charge battery; press POWER button to turn on.
Solar not charging	Poor sunlight/connection	Reposition panel; check cable connections.
Overload shutdown	Connected load too high	Disconnect devices, restart, connect lower load first.
LCD display blank	Battery save mode	Press any button to wake display; charge if battery low.
Red warning light	Over-temperature	Turn off, move to cooler area, allow to cool before use.

Reset: Hold POWER + MODE for 10 seconds to reset system.

Service: 1-800-555-ENERGY; www.gasolarxy.com/support