Evosanitary 15WG15-15 Manual

The Evosanitary 15WG15-15 is a 15-inch Wall-Mounted Germicidal UV-C Light Fixture designed for surface and air disinfection in healthcare, commercial, and institutional settings. It features a 15-watt UV-C lamp, a durable metal housing with a protective grille, a built-in motion sensor for safety, a programmable timer, wall-mount brackets, and a remote control for operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Safety Features 7. Operation 8. Maintenance & Lamp Replacement 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: UV-C Germicidal Lamp, Metal Housing with Protective Grille, Motion Sensor, Timer Control Unit, Remote Control, Wall-Mount Brackets.

Feature	Description
UV-C Lamp	15-watt germicidal lamp for effective disinfection
Motion Sensor	Automatically turns off UV-C when motion is detected for safety
Programmable Timer	Set automatic on/off cycles (1-240 minutes)
Remote Control	Wireless operation from a distance
Wall-Mount Brackets	For secure mounting on walls or ceilings
Protective Grille	Prevents direct contact with the lamp
Power Indicator LED	Shows operational status
Manual Override Switch	For direct control at the unit
Safety Lock	Prevents unauthorized operation
AC Power Input	For 120V AC, 60Hz connection

Installation

Unpack and inspect contents. Ensure mounting location is suitable.

Choose Mounting Location: Select a wall or ceiling area 7-10 feet above floor, away from direct human occupancy during operation.
Mount Brackets: Use provided screws to attach brackets to wall studs or secure surface.
Attach Fixture: Hang fixture on brackets and secure with locking screws.
Electrical Connection: Connect to a dedicated 120V AC outlet. Ensure power is OFF during installation.

WARNING! UV-C radiation is harmful to eyes and skin. Never look directly at the lamp when it is on. Ensure the area is unoccupied during installation and setup.

First-Time Setup

After installation, configure the unit before first use.

Power On: Plug into AC outlet. The power LED will illuminate.
Remote Control Sync: Point remote at sensor, press SYNC button for 3 seconds until LED flashes.
Set Timer: Use remote or manual controls to set desired disinfection cycle duration.
Test Motion Sensor: Walk in front of unit to ensure UV-C turns off automatically.
Set Safety Lock: Enable via remote to prevent unintended operation.

CAUTION! Always verify the motion sensor is functioning correctly before leaving the unit in automatic mode. Perform a visual check without looking directly at the lamp.

Specifications

Model: Evosanitary 15WG15-15
Lamp Type: 15-watt UV-C Germicidal
Coverage Area: Up to 150 sq. ft. for surface disinfection
Timer Range: 1 to 240 minutes programmable
Motion Sensor Range: 10 feet, 120-degree field of view
Housing Material: Powder-coated steel
Mounting: Wall or ceiling mount
Power Requirements: 120V AC, 60Hz, 0.5A
Operating Temperature: 32°F to 104°F (0°C to 40°C)
Dimensions: 15" x 8" x 4"
Weight: 6.5 lbs

Controls and Settings

Access controls via Remote Control or Manual Override Switch on the unit.

Remote Control: POWER ON/OFF, TIMER SET (+/-), MOTION SENSOR ON/OFF, SAFETY LOCK, SYNC, MANUAL OVERRIDE.

Manual Controls (on unit): Power Switch, Timer Dial, Motion Sensor Bypass Button, Status LED.

Timer Settings: Set duration for automatic shut-off. Use remote or dial to select minutes.

Motion Sensor Settings: Enable/disable via remote. When enabled, UV-C turns off if motion is detected within 10 feet.

Safety Lock: Prevents operation without remote authorization. Default code: 0000 (change via remote).

Safety Features

Motion Sensor: Primary safety feature; deactivates UV-C upon detecting movement.

Safety Lock: Requires code to operate, preventing unauthorized use.

Protective Grille: Physical barrier between user and UV-C lamp.

Status Indicators: LED shows power and operational mode.

Automatic Shut-off: Timer ensures unit does not run indefinitely.

IMPORTANT: These safety features do not replace proper operational procedures. Always ensure the area is vacant before activating the UV-C lamp.

Operation

Standard operation for disinfection cycles.

Clear Area: Ensure no people, pets, or plants are in the coverage area.
Activate Safety Lock: Enter code on remote to unlock unit.
Set Timer: Select desired disinfection duration (e.g., 15-30 minutes for a standard room).
Start Cycle: Press POWER ON on remote. UV-C lamp will illuminate, and timer will start.
Monitor: The motion sensor will remain active. If motion is detected, the lamp will turn off immediately.
Cycle End: Unit will turn off automatically when timer expires. A beep may sound.
Ventilate: Allow 5-10 minutes after cycle before re-entering room, as UV-C can produce ozone.

WARNING! Never bypass the motion sensor for occupied spaces. UV-C exposure causes severe eye and skin damage.

Maintenance & Lamp Replacement

Regular maintenance ensures optimal performance and safety.

Cleaning: Unplug unit. Wipe exterior with a dry, soft cloth. Do not use liquids or cleaners on the grille or lamp.

Lamp Replacement (every 9000 hours or ~1 year of typical use):

Unplug unit and wait 15 minutes for cooling.
Remove protective grille (release clips).
Carefully remove old lamp by twisting counterclockwise.
Insert new 15-watt UV-C lamp (compatible model: EVO-UV15), twisting clockwise until secure.
Replace grille and secure clips.
Plug in and test operation.

CAUTION! Handle UV-C lamps with gloves to avoid skin oils reducing effectiveness. Dispose of old lamps according to local regulations for mercury-containing bulbs.

Regulatory Information

This device complies with FCC Part 15 Class B for unintentional radiators. It meets UL 8800 standards for germicidal equipment. UV-C lamps are regulated by the FDA (21 CFR 1040.20). Copyright © 2023 Evosanitary; trademarks of EvoHealth Technologies, Inc. For support, visit www.evosanitary.com or contact 1-800-555-HELP (4357).

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit will not power on	No power / Safety lock engaged	Check outlet and plug; ensure safety lock is disengaged with correct code.
UV-C lamp does not illuminate	Lamp failure / Timer not set	Replace lamp; ensure timer is set to a duration greater than zero.
Motion sensor not working	Obstructed sensor / Settings	Clean sensor lens; ensure motion sensor is enabled in settings.
Remote control not responding	Batteries / Sync lost	Replace batteries; re-sync remote to unit (press SYNC for 3 seconds).
Unit turns off unexpectedly	Motion detected / Timer expired	This is normal safety operation; ensure area is vacant and reset timer if needed.
Unusual noise or smell	Electrical issue / Overheating	Immediately unplug unit and contact technical support. Do not use.

Reset: Unplug unit for 60 seconds to reset control board.

Service: 1-800-555-HELP (4357); www.evosanitary.com/support