Environmentallights.com solar-panel-1200-mah Manual

The Environmentallights.com solar-panel-1200-mah is a portable 1200mAh solar charging panel designed for outdoor and emergency use. It features a high-efficiency monocrystalline solar cell, USB output for charging devices, built-in overcharge protection, water-resistant casing, a kickstand for optimal sun angle, and an integrated 1200mAh battery for energy storage. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Monocrystalline Solar Panel, USB Output Port, Charge Status LED, Integrated 1200mAh Battery, Kickstand, Water-Resistant Casing.

Installation

Unpack and inspect contents. Ensure all components are present and undamaged.

1. Position the solar panel: Place in direct sunlight, away from shadows.
2. Adjust the kickstand: Set angle between 30-60 degrees facing the sun.
3. Initial charge: Allow panel to charge built-in battery for 4-6 hours in full sun before first use.
4. Secure if outdoors: Use carabiner or place on stable surface to prevent tipping.

WARNING! Do not look directly at the sun or place panel near reflective surfaces that may concentrate sunlight. Keep away from children and pets.

First-Time Setup

Prepare the solar panel for its first charging cycle.

1. Fully charge battery: Place in direct sunlight until Status LED turns green (approx. 6-8 hours).
2. Connect device: Use provided USB cable to connect your phone or device to the USB port.
3. Activate output: Press and hold Power Button for 2 seconds until LED lights up.
4. Monitor charging: Red LED indicates active charging; green indicates full charge or standby.
5. Store energy: The built-in battery will store solar energy for later use.

CAUTION! Only use certified USB cables. Do not attempt to disassemble the unit.

Specifications

• Battery Capacity: 1200mAh Lithium-ion.
• Solar Cell Type: Monocrystalline Silicon.
• Output: USB 5V/1A.
• Charging Time: 6-8 hours full sun for complete battery charge.
• Device Charging: Provides approximately 0.5-1 full charge for most smartphones.
• Operating Temperature: -10°C to 50°C (14°F to 122°F).
• Water Resistance: IP54 (splash proof).
• Dimensions: 150mm x 90mm x 10mm (folded).
• Weight: 180g.
• Warranty: 1 year limited warranty.

Controls and Settings

Simple interface with minimal controls for user-friendly operation.

Power Button: Press once to turn USB output ON/OFF. Hold for 2 seconds to force reset.

Status LED Indicators: - Solid Red: Solar panel is actively charging the internal battery. - Blinking Red: Low battery warning (<20% charge). - Solid Green: Internal battery is fully charged. - Blinking Green: USB output is active and charging a connected device. - No Light: Unit is off or in sleep mode.

Kickstand: Adjust to multiple angles for optimal sun exposure throughout the day.

Connecting Devices

Compatible with most USB-powered devices including smartphones, tablets, GPS units, and cameras.

1. Ensure solar panel has adequate charge (Status LED not blinking red).
2. Use a certified USB cable compatible with your device.
3. Connect cable to the solar panel's USB output port.
4. Connect other end to your device.
5. Press Power Button to activate USB output.
6. Blinking green LED confirms charging is in progress.

Tip: For fastest charging, position panel in direct sunlight while charging your device.

Charging & Operation

Maximize efficiency with proper charging techniques.

1. Optimal positioning: Face solar panel directly toward the sun, adjusting every 2-3 hours.
2. Battery storage: The 1200mAh battery stores energy for nighttime or cloudy day use.
3. Simultaneous charging: Panel can charge internal battery and power a device simultaneously.
4. Low-light operation: In cloudy conditions, charging will be slower but still functional.
5. Battery preservation: If not using for extended periods, store with 50% charge in cool, dry place.
6. Auto-sleep: Unit enters sleep mode after 30 minutes of inactivity to conserve power.

WARNING! Do not expose to temperatures above 50°C (122°F). Do not submerge in water.

Safety Features

Overcharge Protection: Automatically stops charging when battery reaches 100%.

Short-Circuit Protection: Safeguards against USB port shorts.

Temperature Control: Reduces charging rate if internal temperature exceeds safe limits.

Reverse Polarity Protection: Prevents damage from incorrect cable connections.

Care & Cleaning

Regular maintenance ensures optimal performance and longevity.

1. Cleaning solar surface: Use soft, dry cloth to remove dust and debris. For stubborn dirt, dampen cloth with water only.
2. Storage: Store in cool, dry place away from direct sunlight when not in use for extended periods.
3. Cable care: Disconnect cables gently by pulling on the connector, not the cable.
4. Battery maintenance: Fully charge and discharge battery at least once every 3 months if not regularly used.

CAUTION! Do not use chemicals, abrasives, or pressurized water. Do not attempt to open or repair the unit.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. CE certified for European market. RoHS compliant (Restriction of Hazardous Substances). Copyright © 2025 Environmentallights.com; all rights reserved. For support, visit www.environmentallights.com/support or contact 1-800-555-ECO1 (3261).

Troubleshooting

Reset: Hold Power Button for 10 seconds to perform hard reset.

Service: 1-800-555-ECO1; www.environmentallights.com/support