Energeeks EG-CIPBATSOLAR2 Quick Installation Manual

The Energeeks EG-CIPBATSOLAR2 is a high-efficiency, plug-and-play solar battery storage system designed for residential energy backup and solar self-consumption optimization. It features a lithium iron phosphate (LiFePO4) battery, integrated hybrid inverter, Wi-Fi monitoring, multiple operation modes, and UL-certified safety protections. Below are key sections for safety, unpacking, installation, commissioning, operation, and troubleshooting.

1. Safety Precautions 2. Unpacking & Inspection 3. Installation Overview 4. System Specifications 5. Mounting the Unit 6. Electrical Connections 7. Commissioning & Setup 8. Operation Modes 9. Monitoring & Maintenance 10. Regulatory & Warranty 11. Troubleshooting

Safety Precautions

Key safety warnings and symbols: High Voltage, Risk of Electric Shock, Fire Hazard, Proper Grounding Required.

Symbol/Notice	Description
⚠ HIGH VOLTAGE	Live electrical parts inside. Disconnect all AC and DC power before servicing.
🔥 FIRE HAZARD	Install in a well-ventilated area away from flammable materials.
⚡ ELECTRIC SHOCK	Only qualified electricians should perform electrical connections.
🔧 PROPER GROUNDING	Unit must be properly grounded according to local electrical codes.
💧 MOISTURE PROTECTION	Install in a dry, indoor location. IP65 rated for outdoor use only with optional enclosure.

Unpacking & Inspection

Unpack carefully and verify all components are present and undamaged.

Open the shipping box and remove packing materials.
Check contents: Battery Unit, Hybrid Inverter, Communication Cables, Mounting Bracket, AC/DC Connectors, User Manual.
Inspect for physical damage (dents, cracks, water exposure).
Note the serial number on the unit label for registration and support.

WARNING! Do not install if any component is damaged. Contact Energeeks support immediately.

Installation Overview

Typical system configuration: Solar Panels → Hybrid Inverter → Battery → Home Loads & Grid.

Select Location: Dry, cool, well-ventilated indoor wall or floor space.
Mount Unit: Secure mounting bracket to wall studs or concrete.
Electrical Connections: Connect DC from solar, AC from grid/load, and battery cables.
Communication Setup: Connect Wi-Fi dongle or Ethernet for monitoring.
Power On & Commission: Follow startup sequence in the Energeeks app.

CAUTION! Unit is heavy (approx. 55 lbs / 25 kg). Use two people for lifting and mounting.

System Specifications

Battery Capacity: 5.12 kWh (expandable to 20.48 kWh).
Battery Chemistry: Lithium Iron Phosphate (LiFePO4).
Continuous Power Output: 3 kW (6 kW peak).
Input Voltage (Solar): 60-150 VDC, MPPT range.
Output Voltage (AC): 120/240V Split-Phase, 60Hz.
Efficiency: >96% (inverter), >98% (battery).
Communication: Wi-Fi, Ethernet, RS485, CAN.
Operating Temperature: -4°F to 122°F (-20°C to 50°C).
Warranty: 10 years or 6000 cycles (70% capacity retention).

Mounting the Unit

Wall or floor mounting options. Ensure structural support for weight.

Wall Mounting:

Locate wall studs or use appropriate anchors for masonry.
Hold bracket against wall, mark drill holes.
Drill holes and secure bracket with provided screws.
Lift unit onto bracket, ensuring it clicks into place.
Secure unit with locking screws at bottom of bracket.

Clearance: Maintain 12 inches clearance on sides, 24 inches front/back for ventilation and service access.

Electrical Connections

AC and DC wiring must comply with NEC (NFPA 70) and local codes.

Turn OFF main grid breaker and solar array DC disconnect.
Connect Battery: Use provided cables between battery unit and inverter. Tighten terminals to 15 Nm.
Connect Solar PV: From PV disconnect to inverter DC inputs (+/-). Observe polarity.
Connect AC Grid/Load: From main panel to inverter AC terminals (L1, L2, N, GND). Use copper wire per specs.
Connect Critical Loads Panel (if used) to inverter output terminals.
Grounding: Connect equipment grounding conductor to inverter ground terminal.

Tip: Use torque wrench for all electrical connections. Label all wires clearly.

Commissioning & Setup

Initial configuration via Energeeks mobile app.

Power Sequence: Turn ON battery switch, then AC grid breaker, then solar DC disconnect.
LED Indicators: Check for steady green light on inverter (normal operation).
App Setup: Download "Energeeks Pro" app, create account, add device via QR code scan.
Network: Connect Wi-Fi dongle or Ethernet. Ensure strong signal.
System Settings: Configure operation mode (Self-Consumption, Backup, Time-of-Use), set battery charge/discharge limits.
Test: Simulate grid outage to verify backup functionality.

WARNING! Do not bypass any safety disconnects. Follow startup sequence exactly.

Operation Modes

Select mode based on energy goals and utility rates.

Mode	Description	Best For
Self-Consumption	Uses solar to power home, excess charges battery, then exports to grid.	Maximizing solar use, reducing imports.
Backup Priority	Keeps battery reserved for grid outages. Grid powers loads normally.	Areas with frequent outages.
Time-of-Use (TOU)	Charges battery during low-cost periods, discharges during peak rates.	Saving money with variable utility rates.
Off-Grid	Islanded operation. Requires sufficient solar/battery. Grid connection disabled.	Remote locations, intentional islanding.

Monitoring & Maintenance

Monitor system performance and perform routine checks.

Monitoring: Use Energeeks app or web portal to view real-time power flow, battery SOC, energy history, and alerts.

Monthly Checks:

Visual inspection for damage, corrosion, loose connections.
Ensure ventilation paths are clear.
Check app for any fault notifications.
Verify battery state of charge is within normal range.

CAUTION! Do not open unit casing. No user-serviceable parts inside. Contact certified technician for internal maintenance.

Regulatory & Warranty

UL 9540 certified for energy storage. Complies with FCC Part 15 Class B. Copyright © 2023 Energeeks Inc. All rights reserved. For support, visit www.energeeks.com/support or contact 1-800-555-ENERGY (3637). Warranty registration must be completed within 30 days of installation.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit not powering ON	No DC/AC power, main breaker off	Check all disconnects and breakers are ON. Verify battery switch is ON.
No grid connection	Faulty wiring, grid voltage out of range	Check AC wiring and voltage at terminals. Ensure grid parameters are within spec.
Battery not charging	Solar input low, communication error	Check solar irradiance and PV connections. Restart system. Check battery comm cable.
App not connecting	Wi-Fi signal weak, incorrect setup	Move router closer or use Ethernet. Re-pair device in app. Check firewall settings.
Fault LED blinking red	Over-temperature, over-current, internal fault	Check ventilation, reduce load. Note fault code and consult manual. Contact support.

Reset: Hold power button for 10 seconds to soft reset. For hard reset, toggle all breakers OFF for 2 minutes, then restart sequence.

Service: 1-800-555-ENERGY; www.energeeks.com/support