Ecoflow RIVER 600 Series User Manual

The Ecoflow RIVER 600 Series is a portable power station designed for outdoor adventures, home backup, and mobile power needs. It features a high-capacity lithium-ion battery, multiple output ports (AC, DC, USB), fast charging via AC wall outlet or car charger, solar charging compatibility, an informative LCD screen, and advanced battery management system. Below are key sections for safety, features, operation, charging, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. First-Time Setup 4. Specifications 5. Controls and Display 6. Charging the Power Station 7. Using Output Ports 8. Solar Charging Guide 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Portable power station unit, AC charging cable, car charging cable, user manual.

FeatureDescription
AC OutputPure sine wave AC outlet for sensitive electronics
USB-A Output PortsStandard USB ports for phones and tablets
USB-C Output PortFast-charging USB-C port for modern devices
DC Output (Car Port)12V DC output for car appliances
LCD ScreenDisplays battery level, input/output wattage, and status
AC Input PortFor fast wall charging
DC Input PortFor car or solar panel charging
Power ButtonTurns the unit on/off
AC Output ButtonEnables/disables the AC outlet
LED LightBuilt-in emergency light with SOS mode

Safety Information

Read all safety instructions before use. Keep the unit in a dry, well-ventilated area.

  1. Do not disassemble, puncture, or incinerate the battery.
  2. Avoid exposure to water, rain, or excessive moisture.
  3. Use only Ecoflow-approved charging cables and accessories.
  4. Do not connect to appliances exceeding the rated output power.
  5. Keep away from children and pets.

WARNING! Risk of fire or explosion if battery is damaged or misused. Do not charge near flammable materials.

First-Time Setup

Unpack and inspect contents. Fully charge before first use.

  1. Initial Charge: Connect the AC charging cable to the unit and a wall outlet. Charge until LCD shows 100%.
  2. Power On: Press and hold the Power Button for 2 seconds to turn on the unit.
  3. Check Display: Verify battery level and output status on the LCD screen.
  4. Test Outputs: Connect a small device (e.g., phone) to a USB port to ensure functionality.

CAUTION! Ensure the unit is placed on a stable, flat surface during charging and use.

Specifications

Controls and Display

The LCD screen provides real-time information. Front Panel: Power Button, AC Output Button, LED Light Button.

LCD Display Icons: Battery percentage, Input/Output power (W), Estimated runtime, Warning indicators (overload, high temperature).

Settings: Press and hold the Power Button and AC Button simultaneously for 3 seconds to enter settings menu (if applicable). Adjust screen brightness, set auto-shutdown timer, enable/disable beep sounds.

Charging the Power Station

Three charging methods: AC wall outlet, car charger, solar panels.

  1. AC Charging: Use provided AC cable. Connect to unit and wall outlet. Charging time: ~1.6 hours to 80%, ~3 hours to 100%.
  2. Car Charging: Use provided car charging cable. Plug into vehicle's 12V outlet (cigarette lighter). Charging time: ~6-8 hours to full.
  3. Solar Charging: Connect compatible solar panel to DC Input port. Ensure solar panel voltage is within 10-25V range.

Tip: For battery health, avoid leaving the unit at 0% or 100% charge for extended periods.

Using Output Ports

Supports simultaneous use of multiple output ports up to total rated power.

  1. AC Output: Press AC Output Button to enable. Connect appliances (e.g., laptop, fan, small TV). Do not exceed 600W continuous.
  2. USB Ports: Plug in USB cables for phones, tablets, lights. USB-C supports fast charging for compatible devices.
  3. DC Car Port: Use for 12V devices like car coolers, air pumps.
  4. LED Light: Press LED button to cycle through modes (steady, flashing, SOS).

WARNING! The unit will shut off if overloaded. Disconnect devices and restart.

Solar Charging Guide

Use with Ecoflow solar panels or compatible third-party panels (check specifications).

  1. Connect solar panel to unit's DC Input port using appropriate cable.
  2. Place solar panel in direct sunlight. Angle towards the sun for optimal charging.
  3. Monitor input wattage on LCD screen. Ideal conditions yield up to 200W input.
  4. Charging time varies based on sunlight intensity and panel wattage.

CAUTION! Do not look directly at solar panel surface. Keep panel and cables away from water.

Care & Maintenance

Store in a cool, dry place. Clean with a dry, soft cloth. Do not use liquids or abrasive cleaners.

Battery Care: For long-term storage, charge to 60-80% and recharge every 3 months. Avoid extreme temperatures.

CAUTION! Do not attempt to open or repair the unit. Contact Ecoflow support for service.

Regulatory Information

FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. Copyright © 2023 Ecoflow. All rights reserved. For support, visit support.ecoflow.com or contact 1-800-ECOFLOW.

Troubleshooting

SymptomPossible CauseCorrective Action
Unit will not turn onBattery depletedConnect to power source and charge. Press and hold Power Button.
No output from portsOutput disabled/overloadEnsure AC Output Button is on. Check for overload; disconnect devices and restart.
Slow chargingLow input powerUse original charging cable. For solar, ensure adequate sunlight.
LCD screen blankSleep mode/batteryPress any button to wake. If still blank, charge the unit.
Overheating warningHigh ambient temperature/overloadMove to cooler location. Stop charging/discharging until unit cools down.

Reset: Disconnect all devices, turn off unit, wait 1 minute, then restart.

Service: 1-800-ECOFLOW; support.ecoflow.com

Ecoflow RIVER 600 Series User Manual © - All Rights Reserved 2025