Eco-Worthy FD-100W User Manual

The Eco-Worthy FD-100W is a 100-watt portable solar power station designed for outdoor activities, emergency backup, and off-grid power needs. It features a high-capacity lithium battery, multiple output ports (AC, DC, USB), MPPT solar charge controller, LCD display for system status, overload protection, and a durable, weather-resistant casing. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging and Power Management 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, Solar charge controller, LCD status panel, AC output socket, DC output ports, USB charging ports, Car charger port, Solar input terminals.

Feature	Description
Battery Capacity	100Wh Lithium-ion battery
AC Output	110V/60Hz pure sine wave output
DC Output	12V/10A regulated DC output
USB Ports	Two USB-A (5V/2.4A) and one USB-C (PD 18W)
Solar Input	Supports up to 150W solar panel input
LCD Display	Shows battery level, input/output power, and status
Car Charger Port	12V/24V vehicle charging input
Overload Protection	Automatic shutdown on overload or short circuit
Weight	Approximately 2.2 kg (4.85 lbs)
Operating Temperature	-10°C to 40°C (14°F to 104°F)

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect to AC wall charger or solar panel for first-time charging.
Solar Panel Connection: Connect solar panel to solar input terminals (red to positive, black to negative).
Device Connection: Plug devices into appropriate output ports (AC, DC, USB).
Positioning: Ensure unit is placed in well-ventilated area away from direct sunlight or moisture.

WARNING! Do not expose to water or extreme temperatures. Keep away from flammable materials.

First-Time Setup

Power on unit; check LCD display for status.

Initial Charge: Charge fully using included AC adapter before first use.
LCD Display: Verify battery level shows 100% after full charge.
Output Selection: Press power button to activate desired output ports.
Solar Setup: Angle solar panel towards sun for optimal charging.

CAUTION! Ensure all connections are secure before powering on.

Specifications

Model: FD-100W
Battery Type: Lithium-ion
Battery Capacity: 100Wh (27,000mAh/3.7V)
AC Output: 110V AC, 60Hz, 100W max
DC Output: 12V DC, 10A max
USB Output: USB-A: 5V/2.4A; USB-C: 5V/3A, 9V/2A, 12V/1.5A
Solar Input: 12-24V DC, 150W max
Car Charger Input: 12V/24V DC
Dimensions: 19 x 12 x 10 cm (7.5 x 4.7 x 3.9 inches)
Weight: 2.2 kg (4.85 lbs)

Controls and Settings

Access controls via front panel buttons and LCD display.

Front Panel: Power Button, LCD Display, Output Port Selector, Solar Charge Indicator.

LCD Display: Shows battery percentage, input/output power, charging status, error codes. Settings: Output voltage selection (AC/DC), battery saver mode, LCD backlight timeout. Protection: Overload protection, short circuit protection, over-temperature protection, low-voltage cutoff.

Connecting Devices

AC Devices: Plug into AC output socket. DC Devices: Use DC output ports with appropriate adapter. USB Devices: Connect to USB-A or USB-C ports.

Check device power requirements before connecting.
Ensure total load does not exceed 100W.
Press power button to activate corresponding output port.
Monitor LCD display for power consumption and battery level.

Tip: Start with low-power devices to test functionality.

Charging and Power Management

Supports solar, AC wall, and car charger inputs.

Solar Charging: Connect solar panel; ensure proper alignment for maximum efficiency.
AC Charging: Use included AC adapter for fastest charging (approx. 5-6 hours).
Car Charging: Connect to vehicle 12V/24V socket while driving.
Battery Saver Mode: Enable in settings to extend battery life.
LCD Monitoring: Check input power and estimated charging time on display.
Charging Priority: Solar and AC charging can be used simultaneously.

WARNING! Use only recommended charging accessories. Do not charge in extreme temperatures.

Safety Features

Overload Protection: Automatic shutdown if load exceeds 100W. Short Circuit Protection: Cuts power on detected short circuit. Temperature Control: Reduces output or shuts down if overheating. Low Voltage Protection: Automatically turns off when battery drops below 10%.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth only; do not use liquids.

CAUTION! Do not disassemble unit. Avoid dropping or subjecting to strong impacts.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. CE Certified: Meets European safety standards. RoHS Compliant: Free of hazardous substances. Copyright © 2023 Eco-Worthy; all rights reserved. For support, visit www.eco-worthy.com or contact [email protected].

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery depleted/overload	Charge battery; reduce connected load; check for overload protection.
Solar not charging	Poor sunlight/connections	Reposition solar panel; check cable connections; ensure proper polarity.
LCD display blank	Battery completely drained	Connect to AC charger for 30 minutes before use.
Device not working	Power requirement mismatch	Check device power rating; ensure it's below 100W.
Overheating	High ambient temperature/overload	Move to cooler location; reduce load; allow to cool down.

Reset: Disconnect all devices, turn off power, wait 1 minute, then restart.

Service: [email protected]; www.eco-worthy.com