Eco-Worthy 12 Manual

The Eco-Worthy 12 is a 12-volt solar power system designed for off-grid applications, featuring a high-efficiency monocrystalline solar panel, PWM charge controller, deep-cycle battery, power inverter, and comprehensive wiring kit. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Monocrystalline Solar Panel, PWM Charge Controller, Deep-Cycle Battery, Power Inverter, Wiring Kit with Connectors.

Feature	Description
Solar Panel	100W monocrystalline with high conversion efficiency
Charge Controller	PWM type with LCD display for monitoring
Deep-Cycle Battery	12V 100Ah sealed lead-acid battery
Power Inverter	300W pure sine wave output
Wiring Kit	Includes cables, connectors, and mounting hardware
LCD Display	Shows battery voltage, charging current, and load status
Overload Protection	Automatic shutdown on excessive load
Short-Circuit Protection	Built-in protection for all components
Low Voltage Disconnect	Prevents battery over-discharge
USB Output	5V/2.1A USB port for charging devices

Installation

Unpack and inspect all components. Choose a suitable location with maximum sunlight exposure.

1. Mount Solar Panel: Secure panel using mounting brackets facing south (northern hemisphere).
2. Connect Charge Controller: Connect solar panel to controller input, battery to controller output.
3. Connect Battery: Attach battery cables to battery terminals (red to positive, black to negative).
4. Connect Inverter: Connect inverter to battery terminals for AC power output.
5. Ground the System: Connect grounding wire to proper earth ground.

WARNING! Install in dry location away from flammable materials. Use proper personal protective equipment during installation.

First-Time Setup

After installation, power on system and configure settings.

1. Initial Charge: Allow solar panel to charge battery for 8 hours before first use.
2. Configure Charge Controller: Set battery type (sealed, gel, flooded) via controller menu.
3. Set Load Parameters: Configure low voltage disconnect and load timing if applicable.
4. Test Output: Connect small load to verify proper operation.
5. Monitor Performance: Check LCD display for proper charging and battery status.

CAUTION! Never connect solar panel directly to battery without charge controller. Ensure all connections are tight and corrosion-free.

Specifications

• Solar Panel: 100W Monocrystalline, 18V Vmp, 5.56A Imp
• Charge Controller: PWM, 10A max, 12V/24V auto detection
• Battery: 12V 100Ah Deep Cycle Sealed Lead Acid
• Inverter: 300W Pure Sine Wave, 12V DC Input
• USB Output: 5V/2.1A
• Operating Temperature: -20°C to 60°C
• Panel Dimensions: 1040 × 670 × 30 mm
• Weight: 8.5 kg (panel), 30 kg (battery)
• Warranty: 25-year linear power output, 5-year materials

Controls and Settings

Access settings via charge controller buttons and LCD display.

Charge Controller Display: Shows battery voltage, charging current, load current, battery percentage.

Button Functions: MENU (access settings), ENTER (select/confirm), UP/DOWN (navigate/adjust values).

Configurable Settings: Battery type (SEAL, GEL, FLOOD), charging voltage (14.4V/14.7V), load control mode (manual/timer), low voltage disconnect (10.5V-12V), load timer settings (1-15 hours).

Connecting Devices

Connect DC and AC loads to appropriate outputs.

1. DC Loads: Connect directly to charge controller load terminals (max 10A).
2. AC Devices: Connect to inverter AC outlets (max 300W continuous).
3. USB Devices: Use built-in USB port for phones/tablets.
4. Multiple Loads: Use power strip for multiple AC devices (do not exceed 300W total).

Tip: Calculate total wattage before connecting devices. Start with highest priority loads first.

System Operation

Daily operation and monitoring procedures.

1. Daily Check: Monitor battery voltage and state of charge on LCD display.
2. Charging Status: Green LED indicates charging, red indicates fault or low battery.
3. Load Management: Turn off unnecessary loads during low sunlight conditions.
4. Seasonal Adjustment: Tilt panel angle seasonally for optimal sun exposure.
5. Performance Logging: Record daily power generation and consumption.
6. Automatic Features: System automatically manages charging and load disconnection.
7. Manual Override: Use controller buttons to manually turn load on/off.
8. Battery Equalization: Perform every 3 months for flooded batteries (if applicable).

WARNING! Do not exceed inverter's rated capacity. Disconnect loads before performing maintenance.

Safety Features

Multiple protection mechanisms: Overcharge protection, Over-discharge protection, Short-circuit protection, Reverse polarity protection, Overload protection, Temperature compensation.

Maintenance & Care

Regular maintenance ensures optimal performance and longevity.

Weekly: Clean solar panel surface with soft cloth and water. Check all connections.

Monthly: Inspect battery terminals for corrosion. Check cable insulation.

Seasonally: Adjust panel tilt angle. Tighten all mounting hardware.

Battery Maintenance: Keep battery clean and dry. Check electrolyte levels (flooded type only).

CAUTION! Never touch electrical connections with wet hands. Wear eye protection when working with batteries.

Regulatory Information

CE Certified: Complies with European safety standards. RoHS Compliant: Free of hazardous substances. IP65 Rated: Weatherproof solar panel. FCC Part 15: Class B digital device. Copyright © 2023 Eco-Worthy. All trademarks property of their respective owners. For technical support, visit www.eco-worthy.com or contact [email protected].

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power output	Battery discharged/Faulty connections	Check battery voltage; verify all connections; ensure solar panel receiving sunlight.
Low charging current	Dirty panel/Shading	Clean panel surface; remove obstructions; check for shadows.
Inverter not working	Low battery/Overload	Charge battery; reduce connected load; check battery connections.
Controller display blank	No power/Reverse polarity	Check battery and solar connections; verify correct polarity.
Battery not holding charge	Old battery/Excessive load	Test battery capacity; reduce power consumption; replace if necessary.
Overload protection triggered	Too many devices connected	Disconnect some loads; restart system; check individual device wattage.

Reset Procedure: Disconnect solar panel and battery for 5 minutes, then reconnect.

Service: [email protected]; www.eco-worthy.com; +1-800-555-ECO1