Ebl S120 User Manual

The Ebl S120 is a versatile portable power station designed for outdoor activities, emergency backup, and mobile power needs. It features a high-capacity lithium battery, multiple output ports (AC, DC, USB), solar charging capability, LCD display for status monitoring, built-in safety protections, and lightweight portable design. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Lithium-ion battery pack, LCD display panel, AC output port, DC output ports, USB charging ports, Solar charging input, Power button, LED indicators.

Feature	Description
AC Output Port	For powering standard household appliances (up to 120W)
DC Output Ports	For 12V devices (car vacuum, cooler, etc.)
USB Charging Ports	For smartphones, tablets, and other USB devices
Solar Charging Input	For recharging via compatible solar panel
LCD Display	Shows battery level, input/output power, and status
Power Button	Turns the power station on/off
LED Indicators	Show charging status and error codes
Overload Protection	Automatically shuts off if overload is detected
Portable Handle	For easy transportation
Wall Charger	For AC wall outlet charging

Installation

Unpack and inspect contents. Place on stable, dry surface.

1. Initial Charge: Connect the included AC adapter to the DC input port and a wall outlet.
2. Connect devices: Use appropriate cables for AC, DC, or USB outputs.
3. For solar charging: Connect compatible solar panel to solar input port (ensure proper sunlight).
4. Power on: Press and hold the POWER button for 3 seconds.

WARNING! Keep away from water and extreme temperatures. Do not disassemble the unit.

First-Time Setup

Power on the unit; check LCD display for battery status.

1. Fully charge before first use: Connect to AC wall charger until LCD shows 100%.
2. Test outputs: Connect a small device (e.g., phone) to USB port to verify operation.
3. Configure settings: Use MODE button to switch between output modes if applicable.
4. Monitor battery: LCD displays remaining capacity and estimated runtime.

CAUTION! Use only provided or recommended accessories. Do not exceed maximum load ratings.

Specifications

• Battery Capacity: 120Wh Lithium-ion.
• AC Output: 120V, 60Hz, 120W max.
• DC Output: 12V/10A.
• USB Output: 5V/2.4A (x2 ports).
• Solar Input: 12-24V, 60W max.
• AC Charging Input: 100-240V, 50/60Hz.
• LCD Display: Battery level, input/output power, temperature.
• Safety Protections: Overload, short circuit, over-temperature, low voltage.
• Operating Temp: 32°F to 104°F (0°C to 40°C).
• Weight: Approx. 3.5 lbs (1.6 kg).

Controls and Settings

Front Panel: POWER button, MODE button, LCD display, LED indicators.

LCD Icons: Battery percentage, AC/DC/USB output status, charging indicator, warning symbols.

Output Control: Press POWER to turn on/off. Press MODE to cycle between output ports (if supported). Battery Settings: LCD shows estimated runtime based on connected load. Charging Settings: Automatically detects input source (AC or solar). Safety Settings: Built-in protections activate automatically; unit may shut down if fault detected.

Connecting Devices

AC Devices: Use standard AC cable. DC Devices: Use 12V car adapter cable. USB Devices: Use USB cable.

1. Ensure power station is turned on.
2. Connect device cable to appropriate output port.
3. Device should power on automatically (some may require manual power-on).
4. Monitor LCD for load wattage and battery drain rate.

Tip: Start with lowest power device first to verify operation. Do not connect devices exceeding total 120W.

Charging the Power Station

Supports AC wall charging and solar charging.

1. AC Charging: Connect AC adapter to DC input port and wall outlet. Charging indicator LED will light red, turning green when full.
2. Solar Charging: Connect compatible solar panel to solar input. Ensure direct sunlight for optimal charging.
3. Charging Time: Approximately 6-8 hours from empty via AC; solar charging time varies with sunlight.
4. Simultaneous Use: Can charge devices while the power station itself is charging.
5. Battery Preservation: For long-term storage, charge to 50-60% and store in cool, dry place.

WARNING! Use only recommended solar panels. Do not expose to rain during solar charging.

Safety Features

Overload Protection: Automatically cuts power if total load exceeds 120W. Short Circuit Protection: Detects and disables output if short circuit occurs. Temperature Control: Reduces output or shuts down if internal temperature exceeds safe limits. Low Voltage Protection: Automatically shuts off when battery drops below 10% to prevent damage.

Care & Maintenance

Keep unit clean and dry. Wipe with dry cloth only; do not use liquids or abrasive cleaners.

CAUTION! Do not attempt to open or repair the unit. No user-serviceable parts inside. Store in temperature-controlled environment.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2025 Ebl; trademarks of Ebl Power Company. For support, visit www.eblpower.com or contact 1-800-555-0123.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't turn on	Battery depleted	Connect to AC charger for at least 30 minutes before use.
No output power	Overload protection activated	Disconnect all devices, wait 30 seconds, then reconnect one device at a time.
Slow charging	Low solar input/weak AC source	Ensure solar panel in direct sunlight; use proper AC adapter.
LCD display blank	Battery completely drained	Charge for 1 hour; display should reappear.
Device not charging	Faulty cable/wrong port	Try different cable; ensure correct output port is selected.

Reset: Disconnect all devices, turn off unit, wait 1 minute, then restart.

Service: 1-800-555-0123; www.eblpower.com