Duracell DSP100 User Manual

The Duracell DSP100 is a portable power station designed for reliable backup power and outdoor use. It features a high-capacity lithium-ion battery, multiple output ports (AC, DC, USB), pure sine wave inverter technology, LCD display for monitoring, built-in safety protections, and support for solar charging. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Charging & Power Management 8. Safety Features 9. Care & Maintenance 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: Lithium-ion battery pack, LCD display panel, AC power outlets, DC output ports, USB charging ports, Solar charging input, Power button, LED indicators.

Feature	Description
AC Output	Pure sine wave AC outlets for sensitive electronics
DC Output Ports	12V/10A ports for car accessories and DC devices
USB Charging Ports	USB-A and USB-C ports for mobile devices
LCD Display	Shows battery level, input/output power, and status
Solar Charging Input	MPPT controller for efficient solar panel charging
AC Input	For wall charging from standard outlet
Car Charging Input	12V car adapter for charging on the go
Power Button	Turns unit on/off and controls output ports
Overload Protection	Automatic shutdown on overload or short circuit
Cooling Fan	Thermal management during high load operation

Installation

Unpack and inspect contents. Place on stable, dry surface.

Initial Charge: Connect AC adapter to wall outlet and unit for full charge.
Positioning: Ensure adequate ventilation around unit; keep away from heat sources.
Solar Panel Setup: Connect compatible solar panel to solar input port.
Device Connections: Connect devices to appropriate output ports.

WARNING! Do not expose to water or extreme temperatures. Ensure all connections are secure before operation.

First-Time Setup

Power on unit; monitor LCD display for status.

Initial Charge: Charge fully before first use (8-10 hours via AC).
LCD Calibration: Verify battery percentage matches actual charge.
Output Configuration: Select output modes via power button (AC/DC/USB).
Solar Setup: Connect solar panel in direct sunlight for optimal charging.

CAUTION! Use only Duracell-approved accessories. Do not disassemble unit.

Specifications

Battery Capacity: 1000Wh Lithium-ion.
AC Output: 1000W continuous, 2000W surge.
DC Output: 12V/10A (max 120W).
USB Output: USB-A: 5V/2.4A, USB-C: 60W PD.
Input Charging: AC: 110-240V, Solar: 12-24V, Car: 12V.
Display: LCD with battery level, input/output wattage.
Safety: Overload, short circuit, over-temperature, over-voltage protection.
Operating Temp: 32°F to 104°F (0°C to 40°C).
Weight: 22 lbs (10 kg).

Controls and Settings

Access functions via power button and LCD interface. Front Panel: POWER button, LCD display, AC output switch, DC output switch, USB ports.

LCD Display Indicators: Battery percentage, Input power, Output power, Warning icons, Temperature status.

Settings: Output mode selection (AC/DC priority), Battery saver mode, Display brightness, Fan control (Auto/Manual). Charging: AC charging rate, Solar charging priority, Car charging mode.

Connecting Devices

AC Devices: Plug into AC outlets. DC Devices: Use 12V car adapter cables. USB Devices: Connect to USB-A or USB-C ports.

Turn off device and power station before connecting.
Match device power requirements to appropriate port.
Turn on power station first, then device.
Monitor LCD for power draw and battery level.

Tip: Start with highest priority devices first during limited power.

Charging & Power Management

Supports multiple charging methods and intelligent power distribution.

AC Charging: Connect to wall outlet; full charge in 8-10 hours.
Solar Charging: Connect compatible panel; optimal in direct sunlight.
Car Charging: Use 12V car adapter while driving.
Battery Saver Mode: Extends battery life by reducing non-essential functions.
Priority Charging: Set charging priority in settings menu.
Load Management: Distributes power based on connected device priority.
Auto-shutdown: Powers off after set period of inactivity.
Parallel Use: Can connect multiple units for increased capacity.

WARNING! Do not exceed maximum input/output ratings. Use proper cables.

Safety Features

Overload Protection: Automatic shutdown when exceeding rated capacity. Short Circuit Protection: Cuts power on detected short. Temperature Control: Fan and thermal cutoff prevent overheating. Voltage Protection: Prevents over-charging and over-discharging.

Care & Maintenance

Store in cool, dry place. Clean with dry cloth only; no liquids or chemicals.

CAUTION! Do not expose to moisture. Store at 50% charge if not used for extended periods.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits. UL Certified: Meets safety standards for portable power stations. Copyright © 2025 Duracell; trademarks of Duracell U.S. Operations, Inc. For support, visit www.duracell.com/powerstation or contact 1-800-551-2355.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Unit won't power on	Battery depleted	Connect to power source and charge; check connections.
No output power	Overload protection triggered	Disconnect devices; reset unit; reconnect one device at a time.
Slow charging	Insufficient input power	Use proper adapter; ensure solar panel in direct sunlight.
Overheating	High ambient temperature	Move to cooler location; ensure ventilation; reduce load.
LCD display blank	Sleep mode or fault	Press power button; check battery connection; reset unit.

Reset: Hold power button for 10 seconds to hard reset.

Service: 1-800-551-2355; www.duracell.com/powerstation