Connect CSH-ODSLR-5W User Manual

The Connect CSH-ODSLR-5W is a 5-watt outdoor solar-powered LED security light with motion sensor, dusk-to-dawn operation, adjustable detection range and sensitivity, IP65 waterproof rating, and a built-in 2200mAh lithium battery. It features a wide-angle illumination, three lighting modes (Motion Sensor, Dim Mode, Constant On), and is designed for easy installation on walls, fences, or eaves. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Operation Modes 8. Maintenance & Care 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Solar Panel, LED Light Array, PIR Motion Sensor, Control Panel, Mounting Bracket, Rechargeable Battery.

Feature	Description
Solar Panel	Monocrystalline panel for charging the internal battery
LED Light Array	5W high-efficiency LEDs providing wide illumination
PIR Motion Sensor	Detects movement up to 26 feet with 120° angle
Control Panel	Mode selection and sensitivity adjustment buttons
Mounting Bracket	Adjustable bracket for wall or eave mounting
Rechargeable Battery	2200mAh lithium battery for night operation
IP65 Rating	Dust-tight and protected against water jets
Lighting Modes	Motion Sensor, Dim Mode, Constant On
Dusk-to-Dawn Sensor	Automatically turns on at dusk, off at dawn
Adjustable Head	Light head can be tilted for optimal angle

Installation

Unpack and inspect contents. Choose a location with direct sunlight.

Select mounting location: Ensure at least 6 hours of direct sunlight daily.
Mount the bracket: Use provided screws to secure bracket to wall, fence, or eave.
Attach the light: Slide the light onto the bracket and tighten the locking knob.
Adjust the angle: Tilt the solar panel and light head for optimal sun exposure and coverage.

WARNING! Do not install near heat sources or flammable materials. Ensure mounting surface is stable.

First-Time Setup

After installation, allow the battery to charge fully before first use.

Initial charge: Leave the light in direct sunlight for 8-10 hours to fully charge the battery.
Select mode: Press the MODE button to choose between Motion Sensor, Dim, or Constant On.
Adjust sensitivity: Use the SENS button to set motion detection sensitivity (Low/Medium/High).
Set duration: Use the TIME button to adjust how long the light stays on after motion (10s/30s/1min).

CAUTION! Do not cover the solar panel during charging. Keep sensor area clear of obstructions.

Specifications

Power: 5W LED.
Solar Panel: 2W, Monocrystalline.
Battery: 2200mAh Li-ion, 3.7V.
Light Output: 400 Lumens.
Color Temperature: 6000K (Cool White).
Motion Sensor: Detection range up to 26 ft, 120° angle.
Lighting Time: Up to 12 hours on full charge (varies by mode).
Charging Time: 6-8 hours in full sunlight.
IP Rating: IP65 Waterproof and Dustproof.
Operating Temp: -4°F to 122°F (-20°C to 50°C).

Controls and Settings

Access controls via buttons on the back panel. Control Panel: MODE, SENS, TIME, TEST.

Button Functions: MODE (cycles through lighting modes), SENS (adjusts motion sensitivity), TIME (sets duration light stays on after motion), TEST (manual test of light and sensor).

Modes: Motion Sensor (default), Dim Mode (20% brightness all night), Constant On (100% brightness all night). Sensitivity: Low (reduced range), Medium (standard), High (maximum range). Duration: 10 seconds, 30 seconds, 1 minute (after last detected motion).

Connecting to Power

This is a solar-powered device; no external wiring required.

Ensure solar panel is clean and facing direct sunlight.
The internal battery charges automatically during daylight hours.
For first use or after long storage, charge for 8-10 hours before operation.

Tip: Wipe solar panel with a clean, dry cloth weekly for optimal charging efficiency.

Operation Modes

Three lighting modes available.

Motion Sensor Mode: Light turns on at 100% brightness when motion is detected, then turns off after set duration.
Dim Mode: Light stays on at 20% brightness all night, brightens to 100% when motion is detected.
Constant On Mode: Light stays on at 100% brightness from dusk to dawn.
Testing: Press TEST button to manually activate light for 5 seconds and check sensor operation.
Adjustments: Use SENS and TIME buttons to fine-tune performance to your environment.

WARNING! Do not stare directly into LED lights. Keep away from children's reach.

Maintenance & Care

Regular maintenance ensures optimal performance.

Clean solar panel monthly with soft, damp cloth. Check mounting hardware quarterly for tightness. In winter, remove snow accumulation from solar panel. If not used for extended periods, store in cool, dry place and charge every 3 months.

CAUTION! Do not disassemble the unit. Do not use abrasive cleaners or solvents.

Regulatory Information

FCC Part 15: Class B digital device; complies with interference limits for residential use. Copyright © 2023 Connect; trademarks of Connect Home Solutions, Inc. This product contains lithium-ion battery; dispose of properly according to local regulations. For support, visit www.connecthomesolutions.com or contact 1-800-555-2837.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Light does not turn on	Low battery/obstructions	Ensure solar panel gets direct sunlight; clean panel; charge for 8+ hours.
Motion sensor not working	Settings/placement	Check sensitivity setting; ensure sensor area is clear; adjust angle.
Light stays on all day	Dusk sensor blocked	Clean light sensor window; ensure not installed under permanent cover.
Short lighting duration	Battery/weather	Fully charge battery; performance reduced in cloudy weather.
Dim light output	Mode setting/battery	Check if in Dim Mode; charge battery fully; LEDs may degrade over time.

Reset: Press and hold MODE button for 10 seconds to restore factory settings.

Service: 1-800-555-2837; www.connecthomesolutions.com