Brass Monkey GH2015 Instruction Manual

The Brass Monkey GH2015 is a high-performance portable gas heater designed for outdoor and indoor use in well-ventilated areas. It features a compact design, adjustable heat output, piezoelectric ignition, safety tip-over switch, oxygen depletion sensor (ODS), and runs on standard propane cylinders. Below are key sections for safety, features, assembly, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Assembly & Installation 3. First-Time Setup 4. Specifications 5. Controls and Operation 6. Connecting Gas Supply 7. Safety Features 8. Maintenance & Storage 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: Burner assembly, Piezoelectric igniter, Control knob, Heat reflector, Safety grille, Gas regulator hose, Propane cylinder connection.

Feature	Description
Piezoelectric ignition	Push-button spark ignition, no batteries required
Adjustable heat control	Rotary knob for low/medium/high flame settings
Safety tip-over switch	Automatically shuts off gas if heater is knocked over
Oxygen Depletion Sensor (ODS)	Monitors oxygen levels and shuts off if levels drop
Portable design	Carry handle and lightweight construction
Heat reflector	Directs heat forward for efficient warming
Gas regulator & hose	Includes hose and regulator for standard propane cylinder
Control knob	Combined ON/OFF and heat adjustment
Safety grille	Protective barrier to prevent contact with hot surfaces
Stable base	Wide footprint for stability

Assembly & Installation

Unpack and inspect all parts. Assemble on a flat, stable surface.

Attach the base: Align base with heater body and secure with provided screws.
Install heat reflector: Slide reflector onto front of heater, secure with clips.
Attach safety grille: Position grille over burner area, fasten with screws.
Connect gas hose: Hand-tighten regulator to heater gas inlet; ensure connection is secure.

WARNING! Perform assembly in a well-ventilated area away from open flames or sparks. Ensure all connections are tight before use.

First-Time Setup

Before first use, perform a leak check and ensure proper ventilation.

Leak check: Apply soapy water to all gas connections. If bubbles form, tighten and retest.
Ventilation: Ensure area has adequate fresh air flow (minimum 36 square inches of opening).
Clearance: Place heater on non-flammable surface with 3 feet clearance from combustibles.
Ignition test: Follow lighting procedure to verify proper operation.

CAUTION! Never use heater in enclosed spaces without continuous ventilation. Carbon monoxide poisoning can occur.

Specifications

Model: Brass Monkey GH2015
Heat Output: Adjustable up to 15,000 BTU/hr
Fuel Type: Propane (LPG)
Cylinder: Standard 20 lb propane cylinder (not included)
Ignition: Piezoelectric push-button
Safety Features: Tip-over switch, ODS, flame failure protection
Dimensions: 18" H x 12" W x 10" D
Weight: 8.5 lbs (without cylinder)
Operating Time: Up to 10 hours on high with 20 lb cylinder
Certifications: CSA certified for outdoor/ventilated indoor use

Controls and Operation

Control knob: OFF, PILOT, and heat settings (LOW, MEDIUM, HIGH).

Lighting Procedure:

Ensure gas cylinder valve is closed.
Turn control knob to OFF position and wait 5 minutes.
Open cylinder valve slowly.
Push and turn control knob to PILOT position.
Press and hold piezoelectric igniter button until pilot lights.
Continue holding knob for 30 seconds after pilot is lit.
Turn knob to desired heat setting (LOW, MEDIUM, HIGH).

Shutdown Procedure: Turn knob to OFF, then close cylinder valve.

Connecting Gas Supply

Use only standard 20 lb propane cylinder with OPD (Overfill Protection Device).

Turn heater control knob to OFF position.
Ensure cylinder valve is closed.
Connect regulator hose to cylinder valve hand-tight (do not use tools).
Perform leak check with soapy water solution.
Place cylinder upright beside heater, secure if necessary.

Tip: Always check hose for cracks or damage before each use. Replace hose every 5 years or if damaged.

Safety Features

Tip-over switch: Automatically cuts gas supply if heater tilts more than 45°. ODS: Monitors oxygen, shuts off if levels fall below 18%. Flame failure protection: Cuts gas if flame goes out. Always keep ventilation openings clear.

Maintenance & Storage

Monthly: Clean burner ports with soft brush. Check hose for cracks. Annually: Have qualified technician inspect. Storage: Turn knob to OFF, disconnect cylinder, store in dry place covered.

CAUTION! Never store propane cylinder indoors or in temperatures above 120°F. Always disconnect cylinder when not in use.

Regulatory Information

CSA certified to ANSI Z21.11.2. For outdoor use and indoor use in well-ventilated areas. Propane cylinder sold separately. Warning: This heater consumes air and produces carbon monoxide. Use only in well-ventilated areas. For support, visit www.brassmonkeyheaters.com or contact 1-800-555-HEAT.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Heater won't light	No gas, blocked ports	Check cylinder has gas; clean burner ports; ensure knob in PILOT position.
Pilot lights but goes out	ODS activated, draft	Increase ventilation; check for drafts blowing on pilot.
Yellow or lazy flame	Dirty burner, low oxygen	Clean burner; ensure adequate ventilation.
Gas odor	Leak	Turn off immediately; check connections; perform leak test.
Low heat output	Low gas, blocked	Check gas level; clean burner and reflector; adjust to HIGH setting.

Reset: Turn knob to OFF, wait 5 minutes, relight following procedure.

Service: 1-800-555-HEAT; www.brassmonkeyheaters.com