Bougerv Yuma100 User Manual

The Bougerv Yuma100 is a 100W portable solar panel designed for outdoor use, featuring high-efficiency monocrystalline solar cells, IP67 waterproof rating, foldable design with carrying handle, integrated kickstand, USB-A and USB-C output ports, and a built-in smart IC for optimal charging. Ideal for charging phones, tablets, power banks, and other USB devices. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Monocrystalline solar panel array, USB-A output ports, USB-C output port, Carrying handle, Integrated kickstand, Smart IC charging controller.

Installation

Unpack and inspect contents. Ensure all parts are present.

1. Choose Location: Select an area with direct sunlight, free from shadows.
2. Unfold Panel: Lay the panel flat or use the kickstand to angle towards the sun.
3. Secure Position: Use included stakes or weights in windy conditions (if applicable).
4. Connect Devices: Use appropriate USB cables to connect your devices.

WARNING! Do not install near heat sources or flammable materials. Ensure panel surface is clean and unobstructed.

First-Time Setup

Position the panel for optimal sun exposure and connect your device.

1. Angle Adjustment: Use the kickstand to tilt the panel perpendicular to the sun's rays for maximum efficiency.
2. Connect Device: Plug your device's USB cable into the appropriate output port (USB-A or USB-C).
3. Check Indicator: The LED indicator should light up, showing charging is active.
4. Monitor Charging: Allow time for charging; efficiency depends on sunlight intensity.

CAUTION! Avoid touching the panel surface in direct sunlight for extended periods as it may become hot.

Specifications

• Maximum Power: 100W.
• Cell Type: High-efficiency Monocrystalline Silicon.
• Open Circuit Voltage (Voc): Approx. 21.6V.
• Short Circuit Current (Isc): Approx. 5.8A.
• Output Ports: 2x USB-A (5V/2.4A each), 1x USB-C (5V/3A, 9V/2A, 12V/1.5A).
• Dimensions (Unfolded): Approx. 40 x 21 inches.
• Dimensions (Folded): Approx. 21 x 14 x 2 inches.
• Weight: Approx. 9.5 lbs.
• Operating Temperature: -4°F to 149°F (-20°C to 65°C).
• Ingress Protection: IP67 (Waterproof & Dustproof).

Controls and Settings

The Yuma100 features automatic operation with minimal user controls.

Physical Controls: None required; the Smart IC handles all power management.

Status Indicator: A single LED next to the output ports. - Solid Green: Panel is receiving sunlight and outputting power. - Flashing Green: Device is connected and charging normally. - Off: No sunlight detected or panel is folded/covered.

Smart IC Features: Automatically detects connected devices and delivers optimal voltage/current. Provides over-current, over-voltage, and short-circuit protection.

Connecting Devices

Compatible with most USB-powered devices like smartphones, tablets, cameras, power banks, and LED lights.

1. Ensure the panel is in sunlight and the indicator LED is green.
2. Use a high-quality USB cable compatible with your device.
3. Plug the cable into the appropriate port on the panel (USB-A for standard devices, USB-C for fast-charge compatible devices).
4. Connect the other end to your device. Charging should begin automatically.

Tip: For fastest charging, use the USB-C port with a device that supports USB Power Delivery (PD).

Charging Devices

Optimize your setup for the best charging performance.

1. Maximize Sun Exposure: Position the panel so the sun's rays hit it directly. Adjust throughout the day.
2. Check Connections: Ensure USB cables are fully inserted and not damaged.
3. Device Compatibility: The panel will not charge laptops or devices requiring more than 100W input.
4. Charging Time: Varies greatly based on sunlight, device battery size, and simultaneous device usage.
5. Storage: When not in use, fold the panel, secure the straps, and store in a cool, dry place.

WARNING! Do not attempt to disassemble or modify the panel. Do not expose to extreme temperatures beyond the operating range.

Safety Features

Built-in protections ensure safe operation: Over-current Protection (OCP), Over-voltage Protection (OVP), Short-Circuit Protection (SCP), and Reverse Polarity Protection. The IP67 rating protects against water and dust ingress.

Care & Cleaning

Disconnect all devices before cleaning.

1. Use a soft, dry cloth to wipe the surface.
2. For stubborn dirt, dampen the cloth with water only. Do not use chemicals or abrasive cleaners.
3. Ensure the panel is completely dry before folding and storing.

CAUTION! Never spray water or cleaner directly onto the panel or ports. Do not use pressure washers.

Regulatory Information

FCC Part 15: This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Copyright © 2025 Bougerv; trademarks of Bougerv LLC. For support, visit www.bougerv.com or contact [email protected].

Troubleshooting

Reset: Disconnect all devices, fold the panel, wait 5 minutes, then unfold and reconnect in sunlight.

Service: [email protected]; www.bougerv.com