Bluetti PV380 User Manual

The Bluetti PV380 is a 380W portable solar panel designed for outdoor and emergency power generation, compatible with various Bluetti power stations and other solar generators with MC4 connectors. It features high-efficiency monocrystalline solar cells, a foldable design with a carry handle, built-in kickstands, waterproof construction (IP65), and includes a solar charging cable. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Monocrystalline solar panel array, MC4 output connectors, Foldable design with carry handle, Adjustable kickstands, Protective carry case.

Installation

Unpack and inspect contents. Choose a suitable location.

1. Unfold the panel: Lay flat on ground or stable surface.
2. Deploy kickstands: Adjust to achieve optimal tilt towards the sun.
3. Connect to power station: Use included MC4 cable to connect panel output to power station's solar input.
4. Ensure direct sunlight: Position panel to avoid shading for maximum output.

WARNING! Do not install near heat sources or flammable materials. Keep connector terminals dry before connection.

First-Time Setup

Connect panel to your compatible Bluetti power station.

1. Verify compatibility: Ensure your power station supports solar input and required voltage range.
2. Connect cables: Plug MC4 connectors from panel to power station's solar input port. Match polarity (positive to positive, negative to negative).
3. Position for sun: Adjust panel angle using kickstands to face direct sunlight.
4. Monitor charging: Check power station display to confirm solar charging has initiated.

CAUTION! Connect cables before exposing panel to full sun. Do not look directly at the sun when positioning panel.

Specifications

• Maximum Power (Pmax): 380W
• Open Circuit Voltage (Voc): [Insert Value] V
• Short Circuit Current (Isc): [Insert Value] A
• Optimum Operating Voltage (Vmp): [Insert Value] V
• Optimum Operating Current (Imp): [Insert Value] A
• Cell Type: Monocrystalline Silicon
• Dimensions (Folded): [Insert L x W x H]
• Dimensions (Unfolded): [Insert L x W x H]
• Weight: Approximately [Insert Weight] kg/lbs
• Operating Temperature: -20°C to 65°C (-4°F to 149°F)
• Ingress Protection: IP65
• Connector Type: MC4
• Cable Length: [Insert Length] of included cable

Controls and Connections

The panel has no electronic controls. Power output is managed by the connected power station.

Connections: MC4 output ports (positive [+] and negative [-]).

Physical Controls: Kickstand release latches, carry handle.

Status Indication: Charging status is shown on the connected power station's display.

Connecting to Power Stations

Use only with compatible power stations that accept MC4 solar input.

1. Turn off power station before connecting (recommended).
2. Identify polarity: MC4 connectors are typically marked or color-coded (red for positive, black for negative).
3. Connect securely: Push connectors together until they click.
4. Turn on power station: It should automatically detect solar input and begin charging if conditions are correct.

Tip: For series or parallel connections with multiple PV380 panels, consult your power station manual and use appropriate combiners or cables rated for the total voltage/current.

Optimal Usage Guidelines

For maximum power harvest.

1. Sunlight: Place in direct, unobstructed sunlight. Avoid shadows on any part of the panel.
2. Angle: Adjust tilt angle seasonally. Rough rule: latitude angle in summer, latitude +15° in winter.
3. Cleanliness: Keep glass surface clean from dust, snow, or debris.
4. Temperature: Output decreases slightly in very high temperatures. Ensure rear ventilation.
5. Monitoring: Regularly check connections for tightness and cable for damage.

WARNING! Do not attempt to disassemble the panel. Do not expose to concentrated sunlight or use lenses that focus light on the panel.

Safety Features

Built-in bypass diodes minimize power loss from partial shading. IP65 rating protects against rain and dust. MC4 connectors provide secure, weather-resistant connections.

Important: The panel produces DC voltage when exposed to light, even when not connected to a load. Handle connectors with care.

Care & Storage

Clean surface with soft, damp cloth. Allow to dry completely before folding or storing. Store in a cool, dry place in its protective case. Avoid folding or placing heavy objects on the panel.

CAUTION! Do not use abrasive cleaners or high-pressure water. Do not store in direct sunlight for prolonged periods when not in use.

Regulatory Information

This product complies with relevant safety and EMC standards. For detailed certification information, please refer to the label on the product or the official website. Copyright © [Year] Bluetti. All trademarks are the property of Bluetti or their respective owners. For support, visit www.bluettipower.com or contact customer service.

Troubleshooting

Reset: Disconnect and reconnect all cables. Restart the connected power station.

Service: For technical support, visit www.bluettipower.com or contact customer service.