Berger XT 200 W User Manual

The Berger XT 200 W is a high-performance 200-watt LED floodlight designed for industrial, commercial, and outdoor applications. It features an IP65 waterproof rating, durable aluminum housing, wide beam angle, high luminous efficacy, multiple mounting options, and compatibility with standard AC power. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Power 7. Operation Modes 8. Maintenance & Safety 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: High-power LED array, Aluminum heat sink, IP65-rated housing, Mounting bracket, Power cable with connector.

Feature	Description
Power Rating	200 Watts LED
Luminous Flux	Up to 20,000 lumens
Beam Angle	120 degrees wide flood
IP Rating	IP65 (Dust-tight and protected against water jets)
Housing Material	Die-cast aluminum with thermal management
Input Voltage	100-277V AC, 50/60Hz
Color Temperature	5000K (Daylight White)
Dimming Capability	0-10V dimmable (optional)
Mounting	Wall, pole, or ceiling mount with adjustable bracket
Operating Temperature	-20°C to 40°C

Installation

Unpack and inspect contents. Ensure mounting surface is stable and can support the light's weight.

Choose mounting location: Select a flat, stable surface away from direct water ingress points.
Mount bracket: Use provided screws to secure mounting bracket to surface.
Attach light fixture: Hang the fixture onto the bracket and secure with locking bolt.
Electrical connection: Connect power cable to appropriate AC supply following local electrical codes.
Secure cable: Use cable glands to maintain IP65 rating.

WARNING! Ensure power is turned OFF at the circuit breaker before installation. Use appropriate personal protective equipment.

First-Time Setup

After installation, power on the fixture and verify operation.

Power verification: Turn on circuit breaker; LED should illuminate immediately.
Angle adjustment: Loosen adjustment knob on bracket to aim light beam as needed, then retighten.
Dimming setup (if applicable): Connect 0-10V dimmer wires to compatible controller.
Test operation: Allow fixture to run for 15 minutes to ensure stable performance.

CAUTION! Do not touch LED surface during operation; it becomes hot. Allow to cool before handling.

Specifications

Model: Berger XT 200 W
Power Consumption: 200W
Luminous Efficacy: 100 lm/W
Color Rendering Index (CRI): >80 Ra
Beam Angle: 120°
Input Voltage Range: 100-277V AC
Frequency: 50/60 Hz
Power Factor: >0.9
Total Harmonic Distortion: <20%
Lifespan: 50,000 hours (L70)
Warranty: 5 years

Controls and Settings

This fixture has no user controls on the unit itself. Operation is controlled via the connected power switch or dimmer.

External Dimming (Optional): Connect compatible 0-10V dimmer to the dimming wires (purple and gray). Dimming range is 10%-100% of full light output.

Mounting Adjustment: Loosen the knob on the mounting bracket to adjust vertical and horizontal angle. Tighten securely after adjustment.

Connecting to Power

Connect to standard AC power supply following local electrical regulations.

Turn OFF power at circuit breaker.
Strip power cable ends to appropriate length.
Connect wires: Live (brown) to L, Neutral (blue) to N, Ground (green/yellow) to ⏚.
Secure connections with wire nuts or terminal block.
Ensure cable gland is properly tightened to maintain waterproof seal.

Tip: For installations in wet locations, apply dielectric grease to connections before sealing.

Operation Modes

The fixture operates in continuous illumination mode when powered.

Standard Operation: Connect to power switch for manual on/off control.
Dimmable Operation: Connect to 0-10V dimmer for adjustable brightness.
Photocell Operation (optional): Connect compatible photocell for dusk-to-dawn operation.
Motion Sensor Operation (optional): Connect motion sensor for automated activation.

WARNING! Do not operate in ambient temperatures above 40°C. Ensure adequate ventilation around heat sink.

Maintenance & Safety

Regular inspection ensures optimal performance and safety.

Cleaning: Turn off power and allow to cool. Wipe exterior with soft, dry cloth. For stubborn dirt, use mild soap solution on cloth (not directly on fixture). Rinse with damp cloth and dry thoroughly.

Inspection: Every 6 months, check for: Loose mounting hardware, Corrosion or damage to housing, Water accumulation in housing, Secure electrical connections.

CAUTION! Never open the fixture housing as this will void warranty and IP rating. Do not use abrasive cleaners or high-pressure water jets.

Regulatory Information

Complies with UL 1598, UL 8750, FCC Part 15B, and RoHS directives. This product contains no hazardous materials. Proper disposal is required at end of life according to local regulations. Copyright © 2025 Berger Lighting. All rights reserved. For technical support, visit www.bergerlighting.com or contact 1-800-555-1234.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Light does not turn on	No power	Check circuit breaker; verify power at outlet; check connections.
Flickering light	Loose connection or incompatible dimmer	Tighten all connections; ensure dimmer is 0-10V compatible.
Reduced brightness	Dimmer setting or aging LED	Check dimmer setting; after 50,000 hours, reduced output is normal.
Overheating	Poor ventilation or high ambient temperature	Ensure minimum 6 inches clearance around fixture; reduce ambient temperature.
Water inside housing	Damaged seal or improper installation	Check cable gland tightness; ensure housing seals are intact (warranty service required).

Reset: Turn power off for 30 seconds, then back on.

Service: 1-800-555-1234; www.bergerlighting.com/support